background image

The diagram below describes how to move around the menu structure and enter data. More specifically it
details:

1. How to enter a real number
2. How to choose an option from a list
3. How to enter and navigate around a sub-menu

Using these three procedures the user can enter all applicable data to configure the unit to suit the application.
The options displayed depends on whether the short menu or full menu option is enabled (This can be
selected in the 

SYStEn

sub-menu).

This menu configures the unit to suit the application. The menu covered in this section is the menu structure
for all applications.

The ‘Menu’ mode is protected by a passcode and the user is asked for this when the ‘Menu’ mode is
accessed from the run mode. The passcode is set to the default of 0 and can be changed to any value
between 0 and 65535, setting the value to zero (default) removes the passcode prompt and the passcode
function is disabled.

If enabled this 

gives access to 

the relevant 

alarm setpoints

To revert to ‘Run’

mode, press these
keys up to 4 times

Show electrical

value e.g.

(4 to 20) mA input

Shows secondary

value i.e. 

total or rate

If enabled this will
clear total, and/or 

latched alarms

Perform clear 

function

Show upper 6 

digits of Total

RUN MODE

(RATE OR TOTAL DISPLAYED)

Edit setpoints

menu shortcut

Followed by

Enter menu mode

8.2 RUN MODE OPTIONS

9.0 MENU MODE

9.1 GENERAL MENU NAVIGATION

Cycle around menu items

IIttEEn

n  11

Description

IIttEEn

n  2

2

Description

IIttEEn

n  33

Description

1. Entering

a number

2. Choosing

from
option list

3. Entering

a sub-menu

Enter Value

11 2

2 33 4

4 5

5 6

6

o

oP

Ptt  A

A

o

oP

Ptt  B

B

Description A

Description B

IIttEEn

n  33A

A

Description 3a

IIttEEn

n  33B

B

Description 3b

Shift into

editable values

Shift into

editable values

Shift into

editable values

Escape to reject

change

Cycle around menu

items

Shift into

editable values

Escape to reject

change

Escape to reject

change

Inc to increment

digit

Inc to increment

choice

Enter to

accept change

OR

Enter to

accept change

OR

Page 12

Page 11

Содержание DM3600A














Отзывы: