Page 9
Page 10
REMOTE DIGITALS OPTION
Two isolated digital inputs are available to reset latched alarms, clear peak/valley readings, or for
customised use with TFML.
Simple plug in pre-calibrated units, no dismantling or re-calibration.
POD-3000/02 DUAL RELAY ALARM
Two independent mains rated relay outputs
Contacts
2 x changeover relays with common wiper
Ratings
AC, DC
Maximum Load
5 A @ 250 V, 5 A @ 30 V
Minimum Load
100 mA
Maximum Power
1250 VA, 150 W
Maximum Switching
253 V,125 V
Electrical Life
1 M operations at rated load
Mechanical Life
50 M operations
Termination Standard
5 way tension clamp connector
Optional Screw
terminals
Pulse Mode
Pulse period 100 ms
POD-3000/03 ISOLATED RE-TRANSMISSION
Ranges
(0 to 10) mA (Active or Passive)
(0 to 20) mA (Active or Passive)
(4 to 20) mA (Active or Passive)
Minimum Current Output
0 mA
Maximum Current Output
23 mA
Accuracy
0.07 % F.S.
Resolution
1 part in 30 000
Max. Output Load
See Section 4.3
Max. Ext. Supply Voltage
30 V (Passive mode)
Voltage Effect
0.2 µA/V
Ripple Current
< 3 µA
Isolation
500 VAC
Stability
1 µA/°C
Termination Standard
5 way tension clamp connector
Optional
Screw terminals
Voltage Outputs
Voltage Outputs may be obtained by connecting a external resistor and
selecting the appropriate current range, as shown in the table below.
7.1 PLUG AND PLAY OPTION PODS
RS485 Modbus Communications
DM3600 is available with RS485 serial communications using MODBUS RTU protocol, and can be configured
using Status’ own M-Config software.
Physical Layer
4 wire or 2 wire half duplex RS485
Protocol
MODBUS RTU format
Breakdown Isolation
500 VAC
Maximum Fan out
32 units (can be increased with repeaters)
Termination Standard
RS485
The DM3600 is configured using the three keys on the front panel. The unit has two modes of operation:
The first is ‘Run’ mode. This will automatically be entered 5 s after power-up. This is the principle mode
of operation. There are 6 possible key press combinations, as shown in the ‘Key Press Definitions’ diagram
below. The ‘Run Mode Options’ diagram shows the key presses required to access various states from the
run mode. (See diagram in Section 8.2 overleaf).
The other principle mode of operation is ‘Menu Mode’. The menu navigation method is shown diagrammatically
in the ‘General Menu Structure’ (see Section 9.1).
Once the menu mode has been accessed, the user can use the large ‘Menu Map’ (see Section 10.0) to
navigate through the menu structure.
All programming is done using the three front panel keys, A, B and C.
ESCAPE (A & B), ENTER (B & C) and CLEAR (A & C) are obtained by simultaneously pressing the two keys.
CYCLE (A), SHIFT (B) and INC (C) keys are pressed singularly.
7.2 COMMUNICATIONS OPTION
RESISTOR
CURRENT RANGE
OUTPUT
1 K
Ω
(0 to 10) mA
(0 to 10) V
500
Ω
(0 to 20) mA
(0 to 10) V
250
Ω
(4 to 20) mA
(1 to 5) V
8.0 INSTRUMENT CONFIGURATION
8.1 KEY PRESS DEFINITIONS
CYCLE
SHIFT
INC
ESCAPE
ENTER
CLEAR
B
C
A
B
B
C
A
C
A
CONNECTIONS
Input
Comms + Digitals
5 way tension clamp connector (2 Part)
8 way RJ45 (Supplied with matching plug and 1 m cable)
Communications option fitted.
