State Water Heaters 318258-000, Инструкция по установке и руководство по эксплуатации и уходу

Страница: 4 / 20

4
Figure 3
Residential Garage
Installation
Vehicle
Stop
Drain Drain
Pan
NOTE:
The water heater shall be located so it is not subject
to physical damage by moving vehicles or area fl ooding.
State of California
NOTE:
The water heater must be braced, anchored, or
strapped to avoid moving during an earthquake. Contact
local utilities for code requirements in your area, visit
http://www.dsa.dgs.ca.gov, or call 1-916-445-8100 and
request instructions.
IMPORTANT:
The water heater should be located in an
area where leakage of the tank, connections, condensate
lines or condensate will not result in damage to the area
adjacent to the water heater or to lower floors of the
structure. Due to the normal corrosive action of the water,
the tank will eventually leak after an extended period of
time. Also, any external plumbing leak, including those
from improper installation, may cause early failure of the
tank due to corrosion if not repaired. If the homeowner is
uncomfortable with making the repair a qualified person
should be contacted. A suitable metal drain pan should be
installed under the water heater as shown below, to help
protect the property from damage which may occur from
condensate formation or leaks in the piping connections
or tank.
The pan must limit the water level to a maximum
depth of 2-1/2 inches and be two inches wider than the
heater and piped to an adequate drain.
Locate the water
heater near a suitable indoor drain. Outside drains are
subject to freezing temperatures which can obstruct
the drain line. The piping should be at least 3/4” ID and
sloped for proper drainage. Under no circumstance will the
manufacturer or seller of this water heater be held liable
for any water damage which is caused by your failure to
follow these instructions.
METAL
DRAIN
PAN
AT LEAST 2” GREATER THAN THE
DIAMETER OF THE WATER HEATER.
PIPED TO AN
ADEQUATE DRAIN
The water heater must NOT be placed on its side. It •
should be transported and stored in an upright position.
Remove exterior packaging and place installation
•
components aside.
Inspect all parts for damage prior to installation and
•
start-up.
Completely read all instructions before attempting to
•
assemble and install this product.
After installation, dispose of/recycle all packaging
•
materials.
Location Requirements
Site location
Select a location near the center of the water piping system.
The unit must be installed indoors and in a vertical position
on a level surface. The
fl ooring beneath the water heater
must be able to support the weight of the water heater when
fi lled with water (967 lbs. full).
IMPORTANT:
The water heater must be located in a space
750 cubic feet or larger, and must have unrestricted air fl ow.
As an example, a room that has an 8 foot tall ceiling and is
10 feet long by 9-1/2 feet wide would contain 760 cubic feet.
NOTE:
For optimal ef fi ciency and serviceability, the
following clearances should be maintained: 3 feet on the air
inlet side, 5 feet. on the air outlet side, 6 inches in the back,
and 2 feet in the front.
The water heater should be located in an area not
subject to freezing temperatures. Water heaters located
in unconditioned spaces (i.e., garages, basements, etc.)
may require the water piping, condensate piping, and drain
piping to be insulated to shelter against freezing. The drain
and controls must be easily accessible for operation and
service.
The site location must be free from any corrosive elements
in the atmosphere such as sulfur,
fl uorine, and chlorine.
These elements are found in aerosol sprays, detergents,
bleaches, cleaning solvents, air fresheners, paint, and
varnish removers, refrigerants, and many other commercial
and household products. In addition, excessive dust and
lint may affect the operation of the unit (See “Cleaning the
Filter” section).
The ambient air temperature must also be considered
when installing this unit. In Ef
fi ciency Mode the ambient air
temperature must be above 45°F and below 109°F. If the
ambient air temperature falls outside these upper and lower
limits the electrical elements will activate to meet the hot
water demand and the heat pump does not operate.
NOTE
: Local codes and requirements in your area may
require the installation of your water heater be accomplished
in a way that the bottom element is elevated from the
fl oor at least 18 inches. Ensure that a platform capable of
supporting the combined weight of the water heater and
water (967-pounds) is used.
Figure 2
Metal Drain Pan
Installation