Stat-X SDRP Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

Stat-X SDRP Скачать руководство пользователя страница 10

Fireaway Inc.

Version 1

5852 Baker Road

10/2017

Minnetonka, MN 55345

P/N 19112

10

d. Manual Release Toggle Switch part no. 830003

The Manual Release Switch PN 830003 provides a manual means of actuating the
SDRP control panel. Both Automatic Fire Detection and an NFPA recommended manual
means of system actuation are provided by the SDRP panel. The Manual Release
Switch uses a rugged, proven MIL-26482 metal shell connector to link the manual switch
to the SDRP panel manual release input circuit. The normally open toggle switch used
with the Manual Release Switch is protected by a labeled and latching toggle guard and
stainless steel protective bracket. The powder coated aluminum enclosure is fully potted
and environmentally sealed against water intrusion to IP67 standards. The Manual
Release Switch is electrically supervised by the SDRP panel for Normal, Trouble and
Fire conditions.

Figure 10 PN. 830002 Dimensions

Figure 9 - PN. 830002 Manual Release Toggle Switch

«
...
8
9
10
11
12
...
»

Содержание SDRP























Отзывы:

Нет отзывов