Start Shaphon SH-2012AH-QG Скачать руководство пользователя

Страница: 14 / 66

Beijing Start M&E Technology Development Co., Ltd.

北京斯达微步控制技术有限公司

SH-2012AH-QG

切割机数控系统说明书（

C002

）

Plasma machining case:

execute

Ｍ

07 command.

Note:

This is a very important feature. It will be used repeatedly in pause, return and extend piercing

operations. When preheat is done, pressing [PIERCE] key will start up piercing operation

directly.

[SWOFF]: To shut off all the heavy-current output.

[

Ｓ

↑

]: Push it down to rise the cutting torch and release to stop the torch.

[

Ｓ

↓

]: Push it down to lower the cutting torch and release to stop the torch.

；

3.1.8[1] BLOWUP

The pattern will be magnified one times by one keystroke and it can be magnified to eight times maximum by

three keystrokes.

3.1.9 [2] RESTIT

To restore to normal pattern size.

3.1.10 [X] TEST

If [X] key is pressed, the system will run the program at top speed without executing

Ｍ

command. This

feature is often used to position quickly or check the working size of steel plate. This operation can be paused at any

moment or cancelled by pressing [X] key one more times.

3.1.11 [Y] AU-SPD

Since the manual speed and automatic speed is separate in the system, this key is used to switched between

automatic mode and manual mode to adjust the speed multiplying factor.

3.2. Function selection in AUTO mode

It is allowed to invoke a machining program by means of

EDIT

feature. If a program has been invoked(as long as it is the same

program name), it can be run directly. If the program is invoked from an USB disk, especially a large program, it can be run directly with

USB disk connected instead of saving it into the system.

3.2. 1[F1] SECTION

To assign system to start up machining operation from any section or piercing point.

It is often used when machining needs to start from a certain section or only a part needs being processed.

Refer to

SECTION

feature for details.

3.2.2[F2] MAN

To switch the system to manual mode.

3.2.3[F3] RESBREK

After this function is selected, pressing [

START

] key to fulfill breakpoint restoration. Refer to

RESBREK

feature for details.

3.2.4[F4] VIEW

It is used to test the program for any error. When this feature is selected, the pattern of machining program will

be displayed with a cross cursor at the origin.

[S] key is used to magnify the pattern, one times by one keystroke and eight times maximum by three

keystrokes. [Q] key is used to return the pattern to original size. The display position of pattern is moveable by

pressing [

↑

], [

↓

], [

←

] and/or [

→

] key.

PDF

文件使用

"pdfFactory Pro"

试用版本创建

www.fineprint.com.cn

Содержание SH-2012AH-QG



































































Результаты поиска

Содержание SH-2012AH-QG

Отзывы:

Похожие инструкции для SH-2012AH-QG

Бренды по названию

Популярные бренды

Start Shaphon SH-2012AH-QG, Руководство пользователя

Результаты поиска

Содержание SH-2012AH-QG

Отзывы:

Похожие инструкции для SH-2012AH-QG

Бренды по названию

Популярные бренды