-13-
•
If at anytime you would like to go directly to the Slow Warn (pattern #1), simply press, and
hold the pattern select button for approximately 3 seconds. When the LEDs flash once,
release the button and the light will be in the Slow Warn pattern.
•
If you would like to place the light back into the default pattern (Pattern 28: Alternating Pre-
Pop Tripleflash, Alternating Doubleflash, Alternating Flicker), simply press and hold the
pattern select button until the LED’s flash twice (approx. 6 seconds). Then release the
button and the light should be in the default pattern.
•
Toggle Mode:
Pressing and holding the pattern select button until the LED’s flash three
times (approx. 9 seconds) will toggle the “steady output” for patterns 31 and 32 (i.e. swaps
which arrays are steady burn and which are flashing).
•
Indicator LED:
Pressing and holding the pattern select button until the LED’s flash four
times (approx. 12 seconds) will disable or enable the indicator LED.
•
The light will remember the pattern it was in when turned off and display the same pattern
when re-activated.
21 Slow Warn, Superfast Warn
22 All Singleflash, All Flicker
23 Alt. Double, ALT. Quad w/Post Pop
24 All Double, ALL. Quad w/Post Pop
25 Alt Double, Alt. Pre-Pop Quad, Alt. Quad w/Post
Pop, Alt Flicker
26 All Double, All Quintflash, All Quadflash w/Post
Pop, All Flicker
27 All Quadflash w/Post Pop, All Doubleflash, All
Flicker
28 Alt. Pre-Pop Triple, Alt. Doubleflash, Alt Flicker **
29 Alt. Pre-Pops, Alt. Flicker, Superfast Warn
30 Delta Omega, All. Double, All. Flicker
31 One Output Steady---Other Output Singleflash †
32 One Output Steady---Other Output Short-Long †
33 Warn Medium (Alt. Long Singleflash) †
34 Alt. Short - Alt. Long †
35 Cycle All
† = These Patterns meet
California Title 13 and SAE J595
specifications in Red and Blue versions of the model
ULB42-DLP and ULB44-DLP.
1 Slow Warn *
2 Fast Warn
3 Superfast Warn
4 Warn Fade
5 Pre-Pop Warn
6 All Singleflash
7 Alt. Tripleflash
8 All Tripleflash
9 Alt. Quadflash w/Post Pop
10 All Quadflash w/Post Pop
11 Alt. Quintflash
12 All Quintflash
13 Alt. Pre-pop Quintflash
14 All Flicker
15 Alt. PSU Flicker
16 One Side Pop, Other Side Rapid Fire
17 One Side Rapid Fire, Other Pop
18 Comet 1
19 Comet 2
20 Delta Omega (Flash Rate Sweep)
*
Default Pattern #1
**
Default Pattern #2
Warning LED Pattern List
Indicator LED
Located on the bottom of
The Star Phantom
®
, below the Map Light is an Indicator
LED. When your light is activated in any mode, this LED will flash to alert you to the
lightbar activity in the daylight.
Active Mode
Indicator LED Display
Warning LED Flashing Mode
Fast Flash
DLP LED Flashing Mode
Slow Flash
(overrides Fast Flash)
Warning LED Steady Burn or
DLP Takedown (Steady Burn)
Steady
(overrides Fast or Slow Flash)
Warning LED Burst Mode
Flicker
(overrides Steady, Fast or Slow Flash)
This light may be optionally de-activated if you wish. To do this, while the light is
running, hold down the Pattern Select Button for approximately 12 seconds, until the
light flashes 4 times. This will disable (or enable) the indicator LED.
Operation (CONT'D)
