manualshive.com logo in svg

Star Micronics IFBD-HW03, Руководство по техническим характеристикам продукции, Страница: 31 / 47

Поделиться
Скачать
Star Micronics IFBD-HW03 Скачать руководство пользователя страница 31

 

IFBD-HW03/04 Product Specifications Rev. 0.00 

 

3.4.2. SNMP 

Specification 

 

The SNMP of this product has an SNMP engine that operates with UDP/IP.    It is possible to control 

the product and printer information using the SNMP manager.     

• 

Supports SNMPv1, and MIB-II (RFC1213), Printer-MIB (RFC1759), HostResource-MIB 

(RFC1514), and Star’s PrivateMIB.     

• 

“public” has reading permission for the community name, and the character string 

registered in the “Authentic Community” for the product setting information has writing 

permission.    However, if there is no character string set for the “Authentic Community,” 

the community name “public” has writing permission.     

• 

Restrictions: 

sysContact, sysName, sysLocation are restricted to a maximum of 78 characters (in 

single byte characters).     

1 is always returned for reading values when ifAdminStatus and ifOperStatus are 

read-only.   

3.4.2.1. Support MIB 

The following describes the MIB that is supported by this product.   

 

Name

 

Explanation

 

sysDescr

 

ASCII character string of device name; version number

 

sysObjectID

 

Object ID representing product identification number

 

sysUpTime

 

Amount of time system is running from startup (in units of 10msec) 

 

sysContact

 

ASCII character string of controller name, and contact information 

 

sysName

 

ASCII character string of domain name for device control 

 

sysLocation

 

ASCII character string representing physical location of device 

 

sysServices

 

Value of service of device protocol hierarchy 

 

ifNumber

 

Number of device network interfaces

 

ifIndex

 

Interface identification number

 

ifDescr

 

ASCII character string representing information relating to interface

 

ifType

 

Physical/link protocol interface type

 

ifMtu

 

Maximum possible sending/receiving data gram size

 

ifSpeed

 

Interface transmission speed [bit/sec]

 

ifPhysAddress

 

Interface physical address 

 

ifAdminStatus

 

Interface control status

 

ifOperStatus

 

Interface operating status

 

ifLastChange

 

sysUpTime value when interface operating status changed the last time

 

ifInOctets

 

Number of bytes received by interface 

 

ifInUcastPkts

 

Number of subnetwork unicast packets received and sent by the upper level

 

ifInNUcastPkts

 

Number of broadcast and multi-cast packets received and sent by the upper level

 

ifInDiscards

 

Number of reception packets discarded regardless of being normal packets 
because the buffer is full   

 

ifInErrors

 

Number of reception error packets 

 

ifInUnknownProtos

 

Illegal protocols or number of reception packets discarded because it is an 
unsupported protocol   

 

ifOutOctets

 

Total number of bytes sent 

 

ifOutUcastPkts

 

Number of send request packets with the unicast from the upper protocol 

 

 

3-24

Содержание IFBD-HW03
















































Отзывы:

Нет отзывов