5
ENGLISH
(Original instructions)
u
Injuries caused by touching any rotating/moving
parts.
u
Injuries caused when changing any parts, blades or
accessories.
u
Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u
Impairment of hearing.
u
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning!
The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool , along with
the date code:
:
Warning!
To reduce the risk of injury, the user
must read the instruction manual.
O
Wear safety glasses or goggles.
N
Wear ear protection.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Using an extension cable
Always use an approved extension cable suitable for the
power input of this appliance (see technical data).
The extension cable must be suitable for outdoor use and
marked accordingly. Up to 30 m of 1.5 mm2 HO5VV-F exten-
sion cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of damage,
wear and ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the cable
completely.
Features
This tool includes some or all of the following features.
1. Main handle
2. Lock-on button
3. Variable speed switch
4. Forward/Reverse lever
5. Mode selector switch
6. Sleeve
7. SDS + Drill Chuck
8. Depth Stop
9. Side handle
10. Date code
11. SDS-Plus bit
12. Dust collector
13. Keyless chuck
Assembly
Warning!
Before attempting any of the following operations,
make sure that the tool is switched off and unplugged.
Attaching the side handle (Fig A)
Warning!
When using the tool, please use the side handle (9)
for your safety.
The side handle can be fitted to suit both right-handed and
left-handled users.
u
Turn the grip counter-clockwise until you can slide the side
handle onto the front of the tool.
u
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
Warning!
When using the tool, remember to install the side
handles properly.
Fitting an accessory (Fig A)
u
Clean and grease the shank (11) of the SDS Plus bit.
u
Insert the accessory bar into the SDS + Chuck (7).
u
Push the accessory down and turn it slightly until it fits into
the slots.
u
Pull on the accessory to check if it is properly locked.
The hammering and drilling function requires the acces-
sory to be able to move axially several centimetres when
locked in the tool clamp.
Содержание FATMAX SFMEH200
Страница 1: ...www stanley eu SFMEH200 SFMEH210...
Страница 2: ...2 11 6 7 9 1 5 4 3 2 8 10 A 5 B 4 4 C2 C1 D 11 12 7 E...
Страница 69: ...69 2 RCD RCD 3 4...
Страница 70: ...70 5 u u u u u u u u u u u u u u u MDF...
