Stanley FATMAX FMEG230, Руководство пользователя

Страница: 9 / 24

ENGLISH (Original instructions)
9
Assembly
Warning: To minimize the danger of serious personal
injury, please switch off the tool power and disconnect all
plugs before adjusting or removing/installing any
accessory. Before reassembling the tool, press and release
the trigger switch to make sure the tool is already switched off.
Attaching and removing the wheel guard (Fig. B)
Warning To minimize the danger of serious personal
injury, please switch off the tool power and disconnect all
plugs before adjusting or removing/installing any
accessory. Before reassembling the tool, press and release
the trigger switch to make sure the tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (3) collar over the groove (5)
of the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (20) are tightened.
Removing the guard
1. Loosen the screws (20) on the guard collar.
2. Pull up the guard (3).
Warning : Do not operate the tool when the safety
guard is not in place.
Fitting and removing a grinding wheel (Fig C1, C2, C3)
Warning : Do not use damaged grinding wheels.
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (6) correctly onto the spindle (7)
(Fig. C1).
3. Place the disc (8) on the flange (6) (Fig.C2). When fitting
a disc with a raised center, make sure that the raised
centre (9) is facing the flange (6).
4. Screw the out flange (10) onto the spindle (7) (Fig. C3)
- the ring on the flange (10) must fae towoards the disc
when fitting a grinding disc (A)
- the ring on the flange (10) must face away from the
disc when fitting a cutting disc (B)
5. Press the spindle lock (2) and rotate the spindle (7) until it
locks in position (Fig. C2).
6. Tighten the flange (10) with the two-pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (10) with the two-pin
spanner.
Warning : Do not use a damaged disc.
Attaching the side handle (Fig D)
Warning:
Before using the tool, check that the handle is
tightened securely.
Warning: The side handle should always be used to maintain
control of the tool at all times.
Screw the side handle (4) tightly into one of the holes (11) or
(12) on either side of the gear case.
Preparation before use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
• Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
Use
Instructions
Warning: Always observe the safety instructions
and applicable regulations.
Warning: To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
• Make sure all materials to be grinded are secured in
position.
• Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc.
• Avoid overloading. If the tool becomes hot, let it spin for a
few minutes with no load.
1. Be sure to hold the tool tightly with both hands (one hand
on housing, the other on side handle). Start the tool and
bring the grinding wheel on the workpiece.
2. Keep the edge of the wheel tilted at angle from 15 to 30
degrees against the surface of the workpiece.
3. When using a new grinding wheel, do not operate the
wheel in the B direction, otherwise, it will cut into the
workpiece. When the edge of wheel has been rounded off,
you are free to operate the grinder in either the A or B
direction.
Starting and stopping (Fig A)
Warning:
Before using the tool, check whether the handle is
tightened securely. Check whether the ON/OFF switch is