Stanley FATMAX FMEG230, Руководство пользователя

Страница: 10 / 24

ENGLISH (Original instructions)
10
working normally. Before plugging in the tool to the power
supply, check whether the switch is in the OFF position when
pressing the rear end of the switch.
To start the tool, press the rear end of the switch and slide it
forward. Then press the front end of the switch to lock it. Press
the rear end of the switch to stop the tool.
Warning: Do not switch the tool on or off while
under load conditions.
Proper hand position (Fig G)
Warning: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
Warning: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(figure A), with the other hand on the body of the tool, as
shown in figure G.
Switches
Caution: Hold the body of the tool firmly to maintain control of
the tool at start up and during use and until the wheel or
accessory stops rotating.
Make sure the wheel has come to a complete stop be fore
laying the tool down.
Note: To reduce unexpected tool movement, do not switch the
tool on or off while under load conditions.
Allow the grinder to run up to full speed before touching the
work surface. Lift the tool from the surface before turning the
tool off.
Allow the tool to stop rotating before putting it down.
ON/OFF switch (1) with auto-lock(Fig A)
Warning: Before connecting the tool to a power
supply, be sure the slider switch is in the off position
by pressing the front part of the switch and
releasing. Ensure the slider switch is in the off
position as described above after any interruption in
power supply to the tool, such as the activation of a
ground fault interrupter, throwing of a circuit
breaker, accidental unplugging, or power failure. If
the slider switch is locked on when the power is
connected, the tool will start unexpectedly.
To start the tool, slide the slider switch 1 toward the front of
the tool and press, the tool will keep running. Release
pressure from the switch and the tool will stop.
Lock feature of the ON/OFF switch
Slide slider switch 1 to the front of the tool and press, and the
tool will start. When releasing the switch, keep the switch
pressed down and push it to the front of the tool, and the tool
will keep running. To turn off the tool, press the front portion of
the switch to release it. The switch will spring up, which
means that the tool is in the off-state.
Explanation: Before coming into contact with the object you
are working on, make sure the abrasive wheel is turning at
maximum speed. Before turning off the tool, lift the tool up
from the object you are working on.
Caution: Make sure the abrasive wheel is
completely stopped before putting down the tool.
Rotating the gear case (Fig E)
The gear case is mounted onto the tool casing, and it can be
rotated to give the user a more comfortable experience while
cutting.
The rotating gear case can be turned 90 degrees, 180
degrees, and 270 degrees to the left or to the right.
• Loosen the four screws on the gear case.
• Rotate the gear case till it reaches its ideal location.
• Tighten the four screws on the gear case.
• Ensure that the rotating mechanism is locked.
Warning : Do NOT use the tool when the gear case
is unlocked.
Application on metals
When applying the tool on metals, make sure that a
residual-current device (RCD) is inserted to prevent danger
from metal chips.
If the RCD causes power disconnection, have the tool sent to
an authorized Stanley Fat Max dealer for repair.
Warning : Under extreme working conditions,
conductive dust and grit may accumulate on the
housing interior when handling metal workpieces.
This could create an electric shock hazard as it
weakens the protective insulation in the grinder.
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts daily.
Refer to Maintenance.
Using grinding wheels
Warning: Metal powder accumulates. Excessive
use of the grinding wheel on metals may increase
the risk of electric shock.
To reduce the risk, insert the RCD before use and clean the
ventilation ducts daily. Follow the maintenance instructions
below to blow dry compressed air into the ventilation ducts.