10
GB
Keypad - Battery LED (Figure
Ⓒ
①
)
Battery level indicator LED.
LED ON-CONTINUOUS RED
Battery Life > 25%
LED ON-FLASHING RED
Battery Life < 25%
Battery Safety
Always insert batteries correctly with
regard to polarity (+ and –), as marked on
the battery and the equipment. Do not mix
old and new batteries. Replace all batteries
at the same time with new batteries of the
same brand and type.
WARNING:
Batteries can explode, or leak, and can
cause injury or fire
.
To reduce this risk:
• Carefully follow all instructions and warnings on the
battery label and package.
• Do not mix battery chemistries.
•
Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for
several months.
• Do not short battery terminals.
• Do not charge disposable batteries.
•
Remove dead batteries immediately and dispose of
per local codes.
Installing AA Batteries
Battery Installation/Removal Figure
Ⓔ
Laser Tool
•
Open battery compartment cover by pressing and
sliding out.
•
Install / Remove batteries. Orient batteries correctly
when placing into laser tool (Figure
Ⓔ
).
•
Close and lock battery compartment cover by
sliding in until securely closed.
End of Life
DO NOT
dispose of this product with household waste.
ALWAYS
dispose of batteries per local code.
PLEASE RECYCLE
in line with local provisions for
the collection and disposal of electrical and electronic
waste under the WEEE Directive.
Declaration of Conformity
Stanley Tools declares that the CE Mark has been
applied to this product in accordance with the CE
Marking Directive 93/68/EEC.
This product conforms with IEC/EN60825‑1:2014.
Ease of Use
Level / Point Transfer
•
Using the horizontal laser beam, establish a
horizontal reference plane.
•
Position the desired object(s) until they are aligned
with the horizontal reference plane to ensure
object(s) are level.
Square
•
Using either of the vertical laser beams that cross
the horizontal laser beams, establish a point where
the 2 beams cross.
•
Position the desired object(s) until they are aligned
with both the vertical and horizontal laser beams to
ensure object(s) are square.
Pulse Mode (Figure
Ⓒ②
)
•
Setting laser tool to pulse mode allows use with
optional laser detectors.
Содержание 4V360H
