12
13
3. Insert the nozzle adapter (i.e., needle) into item to be inflated.
4. Follow steps 2 through 6 of the “Inflating Tires or Products With Valve Stems” section.
IMPORTANT:
Small items such as volleyballs, footballs, etc. inflate very rapidly. Keep this in mind when setting pressure. Take
extra care not to over-inflate.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the SureFit™ nozzle connector.
7. Allow the unit to cool before storing away.
8. Store the compressor hose, nozzle and nozzle adapter in the storage compartment.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use,
we recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened
with a mild solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer
to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to
the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly.
Recycling is required. Failure to comply with local, state and federal regulations can result in fines, or
imprisonment.
Contact your local waste management authority to dispose of this product.
PLEASE
RECYCLE
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can
result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12 volt DC charger plug fuse replacement
The fuse in the plug end of the 12 volt DC charger protects the adapter’s charging circuit. If the 120 volt AC charger operates, but
the DC charging adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 8 amp volt fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Charging Adapter.
TROUBLESHOOTING
Unit will not charge
• Make sure the inverter power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.
or
• Make sure the 12 volt DC charger is properly connected to both the unit and a functioning DC power source.
Unit fails to jump-start
• Make sure unit’s jump-starter power switch is in the on position.
• Make sure a proper polarity cable connection has been established.
• Check that unit has a full charge. Recharge unit if necessary.
120 volt AC outlet will not power appliance
• Make sure the inverter power switch is in the on position.
• Make sure you have followed all the steps in the 120 AC portable power supply instructions carefully.
• Make sure the appliance being powered does not draw more than 500 watts
• Refer to the important notes included in that section that explain common problems and solutions.
• Check that unit has a full charge. Recharge unit if necessary.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables.
Three different sized nozzle adapters are supplied. Each nozzle adaptor will screw onto the end of the SureFit™ nozzle
connector at the free end of the compressor hose. The compressor hose with tire fitting is stored in the compressor hose
storage compartment. Refer to the “Features” illustration for locations of compressor hose. The compressor power button and
compressor pressure control buttons are located on the control panel on the front of the unit.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting an appropriate nozzle
adapter to the air hose. The compressor is capable of inflating up to 120 pounds per square inch (psi) pressure. The compressor
can operate long enough to fill up to 3 average sized tires before the battery must be recharged. Return hose to the storage
compartment after use.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
•
Follow all safety instructions found in the “Specific Safety Instructions For Compressors” section of this instruction
manual.
• Recharge this unit fully after each use
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Do not operate compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient
temperatures), as it may overheat. In such event, compressor will automatically shut down. Immediately press the compressor
power button to turn the compressor off. Restart after a cooling down period of approximately 30 minutes.
Inflating Tires or Products With Valve Stems
1. Screw the SureFit™ nozzle connector onto the valve stem. Do not overtighten.
2. Press the compressor power button. A beep will sound and the backlit LCD screen will display the following:
+
–
+
Area Light
Compressor
Battery
Status
USB
–
Psi
The Compressor Icon will light and the digital display will alternately show the flashing pre-set psi value (that was last set by
the compressor pressure control buttons) and the current pressure of the item being inflated (which will light solid).
3. Press the “+” and “–” pressure control buttons to set the desired pressure from a range pre-set values (between 3 and 120),
which will display on the backlit LCD screen. The unit will sound a beep with each press of the buttons (holding the button
speeds up the upward or downward value selection). Once the desired pressure has been entered, release the button and
wait 2 seconds. Another beep will sound and the flashing digital display will show the new selected pressure, as follows:
+
Area Light
Compressor
Battery
Status
USB
–
+
–
Psi
The new selected value is now stored in the unit’s memory until it is manually reset.
4. Press the compressor power button once more to begin inflating. The Compressor Icon will flash and the digital display will
only show the current pressure value (which will light solid) to indicate the compressor is activated. Monitor the pressure on
the LCD screen.
IMPORTANT NOTE:
To interrupt during inflation, press the compressor power button again.
5. When desired pre-set pressure is reached, a long beep will sound and the compressor will automatically stop.
6. Turn off the compressor by pressing the compressor power button again.
7. Unscrew and remove the SureFit™ nozzle connector from the valve stem.
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and tire fitting in storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate nozzle adapter from the storage compartment.
2. Screw the nozzle adapter (i.e. needle) into the SureFit™ nozzle. Do not overtighten.
PPRH5DS_ManualENSP_061914.indd 12-13
6/19/2014 4:16:43 PM