Standard Horizon HX290E Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

HX290E

Page 10

4. GETTING STARTED

4.1 RADIO CARE

CAUTION

Before following the instructions below, insure the battery pack is in place
and firmly connected. Care must be taken if the radio was dropped and
a close inspection may be needed to insure the radio case and gaskets
are in adequate condition.

The design of the

HX290E

allows water to enter between the radio and the

battery pack, however waterproof performance is not compromised.

After using the

HX290E

in salt water environment is recommended to clean

the radio with fresh water by rinsing the battery and radio (separately) under a
sink facet or by dunking in a fresh water. After washing, use a soft cloth to
thoroughly dry all parts of the radio and battery.

This will keep the radio parts and the battery clean and in top operating condi-
tion.

4.2 BELT CLIP INSTALLATION AND REMOVAL



To install the Belt Clip: align the
Belt Clip to the groove of the Bat-
tery pack, then press the Belt Clip
downward until it locks in place
with a “

Click

.”



To remove the Belt Clip: press the
Belt Clip Tab away from the bat-
tery pack to unlock the Belt Clip,
then slide the Belt Clip upward to
remove it.



Belt Clip Tab



«
...
8
9
10
11
12
...
»

Содержание HX290E









































Отзывы:

Нет отзывов

Похожие инструкции для HX290E

Бренд: Kathrein Страницы: 40

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 74

THERMASGARD ALTM 2-VA

Бренд: S+S Regeltechnik Страницы: 16

Tourguide Wireless Transmitter SR 2020 D

Бренд: Sennheiser Страницы: 32

Бренд: FTE Maximal Страницы: 44

Бренд: X10 Страницы: 5

Бренд: Omega Страницы: 24

Бренд: Kantronics Страницы: 10

Бренд: R.V.R. Electronica Страницы: 32

Бренд: Dual Страницы: 33

Бренд: Lotek Wireless Страницы: 36

Бренд: Raymarine Страницы: 68

Бренд: Denon Страницы: 95

Бренд: Icom Страницы: 40

Бренд: Extron electronics Страницы: 2

Бренд: Raymarine Страницы: 75

Бренд: Olson Technology Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды