Stahl ISpac 9146 Series Скачать руководство пользователя страница 25

Страница: 25 / 25

914660330020

2017-11-24·HB00·III·en·00

Cleaning

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

Frequency Transmitter

Field Circuit Ex i

Series 9146

Cleaning

• To avoid electrostatic charging, the devices located in potentially explosive areas may

only be cleaned using a damp cloth.

• When cleaning with a damp cloth, use water or mild, non-abrasive, non-scratching

cleaning agents.

• Do not use aggressive detergents or solvents.

Disposal

• Observe national and local regulations and statutory regulation regarding disposal.

• Separate materials when sending it for recycling.

• Ensure environmentally friendly disposal of all components according to the statutory

regulations.

Accessories and Spare Parts

NOTICE

Malfunction or damage to the device due to the use of non-original components.

Non-compliance can result in material damage.

• Use only original accessories and spare parts from

R. STAHL Schaltgeräte GmbH.

For accessories and spare parts, see data sheet on our homepage

www.r-stahl.com.

Содержание ISpac 9146 Series


























Результаты поиска

Содержание ISpac 9146 Series

Отзывы:

Похожие инструкции для ISpac 9146 Series

Бренды по названию

Популярные бренды

Stahl ISpac 9146 Series, Руководство пользователя

Результаты поиска

Содержание ISpac 9146 Series

Отзывы:

Похожие инструкции для ISpac 9146 Series

Бренды по названию

Популярные бренды