7
2
2
1
2
To bond the second controller, press
twice
on the button “Lane
choice”
1
. The right LED now lights continuously. Now press the
“Bonding button”
2
of the second hand controller. If bonding is
successful, both LEDs will then light continuously. The controller
is now bonded to the connector track and controls the car on the
rear lane.
To display the address set for the speed controller, press once on
the binding button
1
on the top of the speed controller.
The LED
2
will then flash, according to the address set.
1
2
Preparation of start
Before using them for the first time, the 2.4 GHz W hand
controllers should be fully charged. To do this, put the controllers in
the charger and switch on the track. While charging is in progress,
the LED‘s
1
on the hand controllers will flash. When charging is
complete, the LEDs
1
light continuously. By employing a lithium-
polymer battery, the hand controllers can be topped up at any time.
1
1
If the speed controller is not actuated, it switches automatically after
about 30 seconds into energy-saving mode. The speed controller
can be reactivated by pressing the tappet or the lane-change button.
Troubleshooting
In case of any malfunctions, please check the following:
• Is the connector track properly connected in the running direction?
• Are the power pack plugs inserted the right way round?
• Is the battery fully charged?
• Does the LED on the controller flash while charging?
• Is the speed controller bound to the receiver?
• Is the hand controller bonded to the connector track?
• Has the speed controller got a duplicate address assignment?
• Is the connector track in stand-by mode?
Note:
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Maintenance and care
1
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior
to cleaning.
1
Racetrack:
Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
Technical specifications
Output voltage: Toy transformer
14.8 V
2 x 14.8 VA (Carrera EVOLUTION)
lithium polymer rechargeable battery:
3.7 V
180 mAh · 0.7 Wh
Maximum charging time: 2 hours
Frequency: 2.4 GHz
Frequency band: 2400-2483.5 MHz
Transmission power: maximum 10 mW
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is not lit any more.
CURRENT CONSUMPTION < 0.5 watt/0.5W
To end the stand-by mode, switch the connector track off
for about three seconds, then on again. The racetrack will
then once again be in ‘idle’ mode.
4.) To switch off = switch position to OFF
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized “sorting/collecting” sys-
tem in accordance with European directive 2012/19/EU, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are
not going through special collecting, are potentially dangerous for
environment and human health, because of dangerous substance.
Output voltage: Toy transformer
14.8 V
2 x 14.8 VA (Carrera EVOLUTION)
lithium polymer rechargeable battery:
3.7 V
180 mAh · 0.7 Wh
Maximum charging time: 2 hours
Frequency: 2.4 GHz
Frequency band: 2400-2483.5 MHz
Transmission power: maximum 10 mW
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is not lit any more.
CURRENT CONSUMPTION < 0.5 watt/0.5W
To end the stand-by mode, switch the connector track off
for about three seconds, then on again. The racetrack will
then once again be in ‘idle’ mode.
4.) To switch off = switch position to OFF
Requirement for FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including in-
terference that may cause undesired operation.
Changes or modifications not expressly approved by the party re-
sponsible for compliance could void the user’s authority to operate
the equipment.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Warnings
Guidelines and warnings about using the LiPo battery/batteries:
LiPo rechargeable batteries are much more sensitive than the tradi-
tional alkaline or NiMh rechargeables. For this reason all instructions
and warnings must be scrupulously observed. Incorrect treatment of
LiPo rechargeable batteries may cause a fire. In handling, charging
and using the LiPo battery/batteries supplied, you take over all re-
sponsibility for the risks attached to lithium batteries.
• Non-rechargeable batteries must not be recharged!
For recharging batteries, only the charging cradle supplied may be
used. If this instruction is disregarded, there is a risk of fire which may
endanger your health and/or cause damage to property.
NEVER use any other charging unit!
• Rechargeable batteries may only be recharged under adult supervi-
sion. When charging, never leave the battery unattended.
When you recharge the battery, you should always be in the vicinity
to keep watch on the process so that you can react to any possible
problem.
• If the battery swells or deforms during either discharge or charging
process, stop the process immediately. Remove the battery as fast
and as carefully as possible and place it on a safe and open area
away from any flammable materials, and keep it under observation for
at least 15 minutes. If you continue to charge or discharge a battery
which has already started to swell or deform, there is danger of fire!
Even at the slightest sign of swelling or deforming, the battery must
be taken out of service.
• The battery supplied must be charged in a safe place away from
flammable materials.
• Empty batteries must be removed from the toy.
• Store the battery at room temperature (16 - 18 °C) in a dry place.
Do not expose the battery to direct sunlight or any other sources of
heat. Temperatures over 50 °C are generally to be avoided.
• Always recharge the battery after use to avoid the possibility of its
becoming deep discharged. When it is not in use, recharge the bat-
tery from time to time, say every 2-3 months. Failure to observe the
methods of handling described above may lead to defects.
• When changing batteries do not use any sharp or pointed objects or
tools. Avoid damaging the protective foil around the battery at all costs.
• When replacing defective batteries, only the recommended battery
types may be used. Damaged or unusable batteries are hazardous
waste, and must be disposed of accordingly.
• Never throw batteries, rechargeable or otherwise, on the fire or ex-
pose them to high temperatures. This may cause a fire or an explo-
sion.
• The electrolyte and electrolyte vapour in the LiPo batteries are haz-
ardous to health. Always avoid direct contact with electrolyte.
If electrolyte makes contact with skin, eyes or other parts of the body,
it must immediately be washed out or off with plenty of fresh water and
a doctor must be consulted.
• Rechargeable batteries are not toys and must not fall into the hands
of children. Keep batteries inaccessible to children.
• The connector clips / battery connections must never be short-
circuited!
• The toy is only to be operated with a transformer or power pack
designed for use with toys!
• The transformer / the power pack is not a toy!
