background image

 

 

28/33 

Weasel

®

 Lite User Manual  

Weasel

®

 Lite User Manual 

 

 

Fig

12 | Insertion of electrical fuses 

 

4.9  Operation 

 

Turning On/Off  

 
The Weasel can be turned on/off easily by means of the on/off switch on the back. If you have forgotten 
where your Weasel is moving or what it is waiting for (e.g. after manual intervention), simply turn it off 
and on again so that it returns to a comprehensible state. Once switched on, your Weasel will be free 
again and circulate in the loop until it is called again 
 

Stopping 

 
Put an obstacle on the track in order to stop approaching Weasel vehicles. The obstacle must be easily 
visible  on  the  level  of  the  distance  sensors.  You  can  use  a  carton,  for  example.  Note  that  waiting 
Weasels  (e.g.  at  Station  markers)  can  start  automatically  once  they  receive  an  app  signal.  For  this 
reason, place also an obstacle in front of a waiting Weasel if you want it to stop. 
 

Transporting 

 
For  manual  in-house  transport  of  your  Weasel,  you  will  need  the 
service rod. With the service rod, you can handle the Weasel easily 
while keeping an ergonomic posture.  
 
Before  installing  the  service  rod,  stop  the  Weasel  and  turn  it  off. 
Then, put the service rod (1) into the two holes (2) in the back of the 
vehicle. After this, lift the vehicle up by pushing the service rod down 
like a hand truck. Now, the vehicle can be handled easily.  
 

Always switch off the Weasel before moving it manually. To avoid damaging the electronics, make 
sure that the drive wheels of the drive unit are not in contact with the floor while you are manually 

moving the vehicle. 
 

Don't  forget  to  remove  the  service  rod  directly  after  use  in  order  to  avoid  injuries  and  material 
damage (especially when moving under transfer stations). 

 

 
 

Содержание WEASEL LITE


































Отзывы: