SRAM DualDrive 24, Техническое руководство, Страница: 40 / 76

NEW NEW NEW
Technical Manual 2006
38
SRAM T3
ASSEMBLY
Caution:
• Only install additional axle attachments
(e.g. struts) between nut and retaining
washer.
• Cable stop bracket: dimensions
see Fig. 9.
• Axle end must protrude by min. 1 mm
to max. 4 mm beyond the nut (1, Fig. 5).
• Mount the brake lever using a suitable
frame clamp (2, Fig. 4 resp. Fig 11) .
Caution:
Mount the brake lever between the two
straps of the frame clamp.
The clamp must be seated on the frame
without play.
Use a self-locking nut! Tightening
torque: 2 – 3 Nm (18 – 27 in.lbs.).
Caution:
Check that all the brake system
components are functioning properly!
Spoke lengths are approximate values. They must be checked through lacing attempts
and adjusted accordingly.
Tire Size Cross Length MH 3115/3105 Length MH 3125
28 / 36 Holes 28 / 36 Holes 36 Holes
47–406 20" x 1.75 x 2 2 x / 3 x 182 mm / 184 mm —
37–490 22" x 1
3
/
8
— / 3 x — / 228 mm —
47–507 24" x 1.75 x 2 2 x / 3 x 234 mm / 235 mm —
37–540 24" x 1
3
/
8
— / 3 x — / 254 mm —
47–559 26" x 1.75 x 2 2 x / 3 x 258 mm / 262 mm 253 mm
37–590 26" x 1
3
/
8
— / 3 x — / 254 mm 273 mm
47–622 28" x 1.75 2 x / 3 x 289 mm / 292 mm 285 mm
28–622 28" x 1
1
/
8
— / 3 x — / 292 mm 285 mm
32–622 28" x 1
5
/
8
x 1
1
/
4
— / 3 x — / 292 mm 285 mm
37–622 28" x 1
3
/
8
x 1
5
/
8
— / 3 x — / 292 mm 285 mm
28–630 27" x 1
1
/
4
fifty — / 3 x — / 297 mm 287 mm
32–630 27" x 1
1
/
4
— / 3 x — / 297 mm 287 mm
Spoke length table:
A S S E M B L Y H U B
• Lace the wheel as normal. See spoke
length table.
• Place the dust cap (1, Fig. 1) and
sprocket (2) on the driver.
• Push sprocket circlip (3, Fig. 2) onto the
cone of tool sleeve (4). Place tool sleeve
with large diameter on the driver.
• Push the spring end of sliding sleeve (5)
of the tool over the tool sleeve. Thrust
sliding sleeve in direction (6), this forces
circlip into the recess of the driver.
• Remove tool and check that the circlip is
seated correctly.
• Turn dust cap (7, Fig. 3) until the three
lugs (8) are between the three beads (9)
on the sprocket (10).
• Position dust cap and push towards
sprocket until it is felt to lock into place.
• Screw tension chain (2, Fig. 5) into the
axle end.
• Placing the wheel in the rear frame.
• Mount the chain.
• Fit new retaining washer (3,5 mm thick)
on left axle end (1, Fig. 4) . The serrations
must bear against the dropout and the
lug must engage in the dropout slot.
Advice:
For bicycles with chain tensioner use
previous retaining washers (2 pieces,
2 mm thick) – see Tech. Manual 2005.
• Tighten up special type axle nut (1, Fig. 5)
and axle nut at other axle end. Tightening
torque 30 – 40 Nm (266 – 350 in.lbs.).
• Guide tension chain (2) trough
deflection pulley (3).
• Position deflection pulley at axle nut and
push until it is felt to lock into place.
Turn deflection pulley until the circular
area is at the top (4,
Fig. 6) .
1
2
3
4
5
6
10
9
8 7
1 2
2
1
3
4
5
4 5
6
3
Mounting Tool
Part No. 0582 104 000
1
2