background image

Model SR463

i

R-H, SR463

i

R-3H, SR463

i

R-4H Series In-Floor Platform Scale 

Operating and Service Manual 
Part No. MAN463

i

R-H_201118 

 

 Page 17 of 20 

 

S

Instruments, Inc.

600 Young Street, Tonawanda, NY  14150 

Tel:  716-693-5977     Fax:  716-693-5854    URL:  

www.srscales.com

 

email:  

[email protected]

     

  

Copyright 2020

 

S

Instruments, Inc.

 

CALIBRATION cont’d 

 

SETTING CALIBRATION 

 

NOTE:

  Ensure that nothing is in contact with the scale system during this procedure.  Remove 

hands from the system when noting the displayed calibration results.   
 

STEP 1:

  Access the Calibration Switch by breaking the Calibration Seal on the underside of the 

display  extrusion.  Put  the  scale  system  into  the  Calibration  Mode  by  switching  the  calibration 
switch on the display board (Error! Reference source not found.).  

NOTE:  USE A NON-METALLIC DEVICE TO SLIDE THE SWITCH.  FAILURE TO DO 

SO WILL RESULT IN DAMAGE TO THE BOARD

 

STEP  2:

   

Select  known  calibrated  weights,  traceable  to  NIST,  up  to  the  Full  Scale  value 

(maximum capacity).   

STEP 3:

  Press the “

MENU”

 button until “

1000.0Lb FULL

” is displayed.  Set the 

FULL

 value to the 

actual quantity of calibrated weight being used for Full Scale.  Use the “

UP”

 arrow button to select the 

digit  and  the  “

DOWN”

  arrow  button  to  change  digit.    Press  “

ENTER

”  to  save  changes.  Press 

WEIGH

” button to abort any changes.   

STEP 4:

  Press the 

MENU

 button until “

500.0Lb HALF

” is displayed.   

NOTE

:    The  Half-Scale  value  is  a  value  between  zero  and  the  Full  Scale  values.    It  is  usually 

close to half the Full Scale value. 

Set the 

HALF

 value to the actual quantity of calibrated weight being used for Half Scale.  Use the 

UP”

 arrow button to  select  the digit and the “

DOWN”

  arrow button to change the digit. 

 Press 

“ENTER”

 to save changes. Press “

WEIGH

” to abort the changes.  

STEP 5:

  Press 

MENU

 button until “

3 PT CAL

” is displayed.  Press the “

UP”

 arrow button. 

STEP 6:  

Display will read “

ZERO

”.  Ensure that all weight has been removed from the platform 

and press the “

UP” 

arrow button. 

STEP 7:

   Display will read “

ADD HALF

”.  Place the calibrated weight on platform for 

HALF 

Scale.  Allow weight to stabilize.  Press “

UP”

 arrow button to save change. 

STEP  8:

    Display  will  read  “

ADD  FULL

”.  Place the calibrated weight  on platform for 

FULL 

Scale.  Allow weight to stabilize.  Press “

UP” 

arrow to save change.   

STEP  9

:    Press 

“ENTER” 

button  to  save  the  calibration,  or  “

WEIGH

”  button

 

to  exit  without 

saving

.  

 

STEP  10:

    Switch  the  scale  system  out  of  the  Calibration  Mode  on  the  display  board  (Error! 

Reference source not found.).   

NOTE

:  Ensure that no wires have become unplugged during calibration 

STEP  11:

    Calibration  Seal  must  be  placed  over  the  access  hole  on  the  display  extrusion  by 

authorized personnel only. 

Содержание SR463iR-3H





















Отзывы: