SPXFLOW Universal 5000 Industrial Series Скачать руководство пользователя страница 58

Страница: 58 / 58

S PX FLOW, Inc.

611 Sugar Creek Road

Delavan, WI 53115

P: (262) 728-1900 or (800) 252-5200

F: (262) 728-4904 or (800) 252-5012

E: [email protected]

SPX FLOW, Inc. reserves the right to incorporate our latest design and mate-

rial changes without notice or obligation.

Design features, materials of construction and dimensional data, as described

in this bulletin, are provided for your information only and should not be relied

upon unless confirmed in writing.

Please contact your local sales representative for product availability in your

region. For more information visit www.spx.com.

The green “>” is a trademark of SPX FLOW, Inc.

ISSUED 12/2015

Universal 5000
Industrial Series

R OTARY P OS ITIVE D I S PLACE M E NT

PU M P

Содержание Universal 5000 Industrial Series



























































Результаты поиска

Содержание Universal 5000 Industrial Series

Отзывы:

Бренды по названию

Популярные бренды

SPXFLOW Universal 5000 Industrial Series, Инструкция по эксплуатации

Результаты поиска

Содержание Universal 5000 Industrial Series

Отзывы:

Бренды по названию

Популярные бренды