manualshive.com logo in svg

SPX S2045, Инструкция по эксплуатации

Поделиться
Скачать
SPX S2045 Скачать руководство пользователя страница 8

Care of Stainless Steel

Waukesha Cherry-Burrell

Page 8

95-03080

12/2010

Care of Stainless Steel

Stainless Steel Corrosion

Corrosion resistance is greatest when a layer of oxide film is 
formed on the surface of stainless steel. If film is disturbed or 
destroyed, stainless steel becomes much less resistant to corro-
sion and may rust, pit or crack.

Corrosion pitting, rusting and stress cracks may occur due to 
chemical attack. Use only cleaning chemicals specified by a repu-
table chemical manufacturer for use with 300 series stainless 
steel. Do not use excessive concentrations, temperatures or 
exposure times. Avoid contact with highly corrosive acids such as 
hydrofluoric, hydrochloric or sulfuric. Also avoid prolonged con-
tact with chloride-containing chemicals, especially in presence of 
acid. If chlorine-based sanitizers are used, such as sodium 
hypochlorite (bleach), do not exceed concentrations of 150 ppm 
available chlorine, do not exceed contact time of 20 minutes, and 
do not exceed temperatures of 104°F (40°C). Corrosion discolor-
ation, deposits or pitting may occur under product deposits or 
under gaskets. Keep surfaces clean, including those under gas-
kets or in grooves or tight corners. Clean immediately after use. 
Do not allow equipment to set idle, exposed to air with accumu-
lated foreign material on the surface. Corrosion pitting may occur 
when stray electrical currents come in contact with moist stain-
less steel. Ensure all electrical devices connected to the equip-
ment are correctly grounded.

Elastomer Seal 
Replacement Following 
Passivation

Passivation chemicals can damage product contact areas of 
equipment. Elastomers (rubber components) are most likely to be 
affected. Always inspect all elastomer seals after passivation is 
completed. Replace any seals showing signs of chemical attack. 
Indications may include swelling, cracks, loss of elasticity or any 
other noticeable changes when compared with new components.

Содержание S2045















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды