manualshive.com logo in svg

SPX S2045, Инструкция по эксплуатации

Поделиться
Скачать
SPX S2045 Скачать руководство пользователя страница 46

Maintenance

Waukesha Cherry-Burrell

Page 46

95-03080

12/2010

Pedestal Base Mounted 
Pump Housing Lubrication

Waukesha Series S200 Pedestal Pumps are lubricated with NLGI 
grade 2 Lithium Complex Grease. Use only NLGI grade 2 Lithium 
Complex thickened greases to replenish the bearing grease sup-
ply. The location of the grease fittings is indicated in Figure 63.

NOTE: Mixing greases that will not mix with the above products 
can change the viscosity/consistency of the grease resulting in 
bearing damage. If there is doubt remove the bearings, clean and 
re-pack.

For compatible lubricants, contact Waukesha Application Engi-
neering at 1-800-252-5200 or 262-728-1900.

Lubrication Schedule 

NOTE: If operating tem-
peratures are over 158°F. 
(70°C.) reduce hours by 
half for every 
27°F.(15°C.) over the 
operating temperature.

Small Bore/1750 RPM

4400

Small Bore/3500 RPM

2000

Large Bore/1750 RPM

2000

Large Bore/3500 RPM

1000

Servicing the Electric 
Motor

See the motor manufacturer’s instructions for specific service 
information. 

General Service Information

Inspect units at regular intervals.

CAUTION: Do not over-grease. 
Excessive lubrication may dam-
age the unit.

Keep the units clean, and ventilation openings clear of dust, dirt, 
or other debris.

Lubricate the units per manufacturer’s instructions and instruction 
plate on the unit.

WARNING: Disconnect all power 
sources to the unit and discharge 
all parts which may retain an 
electrical charge before 
attempting any maintenance or 
repair. Screens and covers must 
be maintained in place when the 
unit is in operation.

Motor Lubrication Instructions

Some small motors have sealed-for-life bearings which require 
no lubrication.

Greasable bearings are shipped with a high quality wide temper-
ature range grease in the bearings.

Some motors can be greased. Refer to the motor manufacturer’s 
instructions for more information regarding lubrication procedures 
and additional service procedures.

Figure 63  - Grease Fittings on the 

Pedestal Pump

Size/RPM

Hours

Содержание S2045















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды