manualshive.com logo in svg

SPX S2045, Инструкция по эксплуатации

Поделиться
Скачать
SPX S2045 Скачать руководство пользователя страница 28

Operation

Waukesha Cherry-Burrell

Page 28

95-03080

12/2010

Operation

Before proceeding, make sure your pump has been correctly 
installed as described in “Installation” on page 23.

Starting the Pump

1.

If pump has a flush seal option, start the flow of flush water 
(approximately 5 US gallons per hour recommended rate) 
before operating the pump. 

2.

Prime the pump by flooding the pump casing with liquid 

BEFORE

 starting the pump to avoid damage to pump parts. 

See “Priming the Pump With the Feed Source Above Pump 
Level” on page 28 or “Priming the Pump With the Feed 
Source Below Pump Level” on page 29.

3.

Start the pump motor and check the motor rotation to make 
sure it is in the same direction as the arrow on the pump.

4.

Check the pump to see that liquid is flowing and that all piping 
connections and seals are leak-free.

5.

Make sure that the pump is not operating against a closed 
discharge. Continued operation against a closed discharge 
will heat the liquid in the casing to boiling and lead to pump 
damage.

6.

Slowly open the discharge valve until the desired flow is 
obtained. Observe pressure gauges and if pressure is not 
attained quickly, stop the pump and prime it again.

Priming the Pump

Priming the Pump With the Feed Source Above 
Pump Level

1.

Fill the supply tank with liquid; open the supply line valve 
(suction) (item B).

2.

Vent any air trapped in the supply line or casing by opening 
the discharge valve. (item A).

3.

Start the pump.

Figure 22 - Pump Below Supply 

(Feed Source Above Pump Level)

Содержание S2045















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды