Table of Contents
Safety Precautions .................................................................2
Specifications .........................................................................3
General Description ...............................................................4
Operation ................................................................................4
Setup ....................................................................................4
Preparing to Paint .................................................................4
Painting .................................................................................5
Pressure Relief Procedure ...................................................6
Spraying ..................................................................................6
Spraying Technique ..............................................................6
Practice .................................................................................6
Unclogging the Spray Tip .....................................................7
Cleanup ...................................................................................7
Maintenance............................................................................7
General Repair and Service Notes.......................................7
Replacing the PRIME/SPRAY Valve.....................................8
Replacing the Filters .............................................................8
Replacing the Motor Assembly (with Electronic Control) .....9
Replacing the Gears .............................................................9
Replacing the Transducer...................................................10
Servicing the Fluid Section .................................................10
Troubleshooting ...................................................................12
Parts Listings........................................................................18
Main Assembly....................................................................18
Drive Assembly ...................................................................19
Fluid Section Assembly ......................................................20
Upright Cart Assembly ........................................................21
Filter Assembly ...................................................................21
Suction Set Assembly (low boy) .........................................22
Low Boy Cart Assembly......................................................22
Labels .................................................................................22
Electrical Schematic ...........................................................23
Accessories ........................................................................23
Limited Warranty ..................................................................24
Safety Precautions
This manual contains information that must be read and
understood before using the equipment. When you come to an
area that has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
This symbol indicates a potential hazard that may cause
serious injury or loss of life. Important safety information will
follow.
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to prevent
damage to the equipment or how to avoid causes of minor
injuries will follow.
IMPORTANT SAFETY INSTRUCTIONS
A. SAVE THESE INSTRUCTIONS – To reduce the risks of
fire or explosion, electrical shock, and the injury to
persons, read and understand all instructions
included in this manual. Be familiar with the controls
and the proper usage of the equipment.
B. WARNING – To reduce the risk of fire or explosion:
1. Do not spray flammable or combustible materials near
an open flame, pilot lights or sources of ignition such
as hot objects, cigarettes, motors, electrical equipment
and electrical appliances. Avoid creating sparks from
connecting and disconnecting power cords.
2. For units intended for use with only water-based
materials — Do not spray or clean with flammable
liquids. For use with water-based liquids only.
WARNING
NOTE: Notes give important information which should
be given special attention.
CAUTION
WARNING
2
© SprayTECH. All rights reserved.
3. For units intended for use with only water-based or
mineral spirit-type materials with a minimum flash point
of 21ºC (69.8ºF) — Do not spray or clean with liquids
having a flash point of less than 21ºC (69.8ºF). Flash
point is the temperature at which a fluid can produce
enough vapor to ignite.
4. Paint or solvent flowing through the equipment is able
to result in static electricity. Static electricity creates a
risk of fire or explosion in the presence of paint or
solvent fumes. All parts of the spray system, including
the pump, hose assembly, spray gun and objects in and
around the spray area shall be properly grounded to
protect against static discharge and sparks. Use only
conductive or grounded high-pressure airless paint
sprayer hoses specified by the manufacturer.
5. Verify that all containers and collection systems are
grounded to prevent static discharge.
6. Connect to a grounded outlet and use grounded
extension cords. Do not use a 3 to 2 adapter.
7. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating
supplier about compatibility of material with aluminum.
8. Keep spray area well ventilated. Keep a good supply of
fresh air moving through the area to keep the air within
the spray area free from accumulation of flammable
vapors. Keep pump assembly in well ventilated area.
Do not spray pump assembly.
9. Do not smoke in the spray area.
10. Do not operate light switches, engines, or similar spark
producing products in the spray area.
11. Keep area clean and free of paint or solvent
containers, rags, and other flammable materials.
12. Know the contents of the paint and solvents being
sprayed. Read all Material Safety Data Sheets (MSDS)
and container labels provided with the paints and
solvents. Follow the paint and solvent manufacture’s
safety instructions.
13. Place pump at least 25 feet (7.62 meters) from the
spray object in a well ventilated area (add more hose if
necessary). Flammable vapors are often heavier than
air. Floor area must be extremely well ventilated. The
pump contains arcing parts that emit sparks and can
ignite vapors.
14. Plastic can cause static sparks. Never hang plastic to
enclose spray area. Do not use plastic drop cloths
when spraying flammable material.
15. Fire extinguisher equipment shall be present and
working.
C. WARNING – To reduce the risk of skin injection:
1. Do not aim the gun at, or spray any person or animal.
2. Keep hands and other body parts away from the
discharge. For example, do not try to stop leaks with
any part of the body.
3. Always use the nozzle tip guard. Do not spray without
the nozzle tip guard in place.
4. Only use a nozzle tip specified by the manufacturer.
HAZARD:
Injection injury – A high pressure fluid stream produced
by this equipment can pierce the skin and underlying
tissues, leading to a serious injury and possible
amputation. See a physician immediately. DO NOT
TREAT AN INJECTION AS A SIMPLE CUT.
WARNING
All manuals and user guides at all-guides.com
