background image

SPRAYEZ-3000  Polyurethane  Proportioner  User Manual

 

WARNING 

PRESSURIZED ALUMINUM PARTS HAZARD 
Use of fluids  that 

are 

incompatible  with aluminum  in

pressurized equipment can cause serious chemical reaction and 
equipment rupture. Failure  to follow  this warning can result  in 
death,  serious injury,  or property damage. 

Do  not  use  1,1,1-trichloroethane,  methylene  chloride,  other
halogenated  hydrocarbon  solvents  for  fluids  containing  such
solvents.

Many  other  fluids  may  contain  chemicals  that  can  react  with
aluminum. Contact your material supplier for compatibility.

EQUIPMENT MISUSE HAZARD 
Misuse can cause death or serious injury. 

This equipment is for Professional use only.

Do  no  leave  the  work  area  while  the  equipment  is  energized  or
under pressure. Turn off all equipment when the equipment is not
in use.

Do  not  operate  the  unit  when  fatigued  or  under  the  influence  of
drugs or alcohol.

Do  not  exceed  the  maximum  working  pressure  or  temperature
rating of the lowest rated system component. See Technical Data
in all equipment manual.

Use fluids and solvents that are compatible with equipment wetted
parts. See Technical Date in all equipment manuals. Read fluid and
solvent manufacturer’s warnings. For complete information about
your material, request MSDS forms from distributor or retailer.

Check equipment daily. Repair or replace worn or damaged parts
immediately with genuine manufacturer’s replacement parts only.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your  distributor
for information.

Route  hoses  and  cables  away  from  traffic  areas,  sharp  edges,
moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

Содержание SPRAYEZ-3000






























Отзывы: