manualshive.com logo in svg

Sports Attack CRICK ATTACK, Инструкция по эксплуатации, Страница: 7 / 17

Поделиться
Скачать
Sports Attack CRICK ATTACK Скачать руководство пользователя страница 7

CRICK ATTACK™ CRICKET BOWLING MACHINE

Sports Attack, LLC. 

•

 800.717.4251 

•

 www.sportsattack.com

5

Set-up & Pr

epar
ation

CRICKET 

SET-UP & PREPARATION

1.  Install the rear leg (

Note:

 the leg has a push button, which locks the leg into the  

socket). Roll Crick Attack into position at the bowlers end.

2.  Be sure the horizontal swivel lock is tightened securely.
3.   Tilt Crick Attack forward until it rests on the throwing wheel guard.

1.  Insert the two front legs into the front sockets in the undercarriage  

(

Note

: the front legs also have locking push buttons).

2.  See Figure 2 on page 4. 

Walk around to the front of Crick Attack, and, with your back to home plate, reach  

down and grasp the wheel guards. Then, lift Crick Attack up and over the front legs  

and set it gently onto the rear leg.

3.  Position Crick Attack: 

 

a.   To approximate the release point of a live bowler, position Crick Attack 

 

      so that the rear leg is level with the stumps (TBC).

 

b.  Then, sight down ball chute. Move the swing control right or left to adjust  

 

      machine so that it is pointing directly at home plate.

 

c.    Check the horizontal swivel lock to make sure it remains tight.

4.  Unlock the travel lock. Turn the handle of the elevation control counter-clockwise  

until the bar of the travel lock snaps back out of the way.

5.  Adjust the throwing head:
 

a.  Turn the handle of the elevation control clockwise. Raise the throwing head    

 

     until it will throw somewhere near the required height.

 

b.   This initial adjustment will come through experience. To start, turn the  

 

      elevation adjustment 10 turns clockwise.

6.  Examine Crick Attack for condition and completeness:
 

a.   Be sure the horizontal swivel lock is secured.

 

b.   Throwing wheels must be tight on the motor shafts. Check that the keyway 

                   retaining bolts are tight.
 

c.   Wheel guard and ball chute must be securely fastened to the throwing head.

7.  Be certain on/off switch is turned “OFF”, then plug Crick Attack into an extension  

cord or other power source. (See generator information at right if applicable.)

WARNING 

HAZARD FROM  

HIGH-SPEED  

PROJECTILES

Being struck by a pitched ball 

can cause serious injury or death. 

Make sure that no one steps in 

front of Crick Attack while it is 

connected to electric power.
Clear all hitters away from home 

plate, the batter’s box and the 

backstop area before connecting 

Crick Attack to electric power.

GENERATOR  

INFORMATION

1.  Crick Attack requires a  

generator capable of 

providing clean electric-

ity 2000 watts at 120 volts 

60hz.

2.  Be sure the on/off switch  

is “OFF” before plugging 

Hack Attack into the  

generator.

3.  Start the generator and 

allow it to reach full speed 

before turning the on/off 

switch “ON”.

IMPORTANT:

 Generator speed 

fluctuations can damage 

the electronic speed control. 

Maintain adequate fuel in the 

generator at all times.

4.  Turn the on/off switch 

“OFF” before shutting off 

the generator and before  

unplugging Crick Attack.

Содержание CRICK ATTACK


















Отзывы:

Нет отзывов