Sports Attack CRICK ATTACK Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 17

Sports Attack CRICK ATTACK Скачать руководство пользователя страница 4

CRICK ATTACK™ CRICKET BOWLING MACHINE

Sports Attack, LLC.

•

800.717.4251

•

www.sportsattack.com

2

Crick A

ttack

™

Safety Instructions

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire 15 amp minimum

rating extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.

OPERATING SAFETY

CAUTION: Never reach down near moving throwing wheels for any reason! If it is

necessary to reach into the throwing wheels, ALWAYS:

1. Turn all three speed dials to “0”.

2. Turn on/off switch “OFF”.

3. Unplug Crick Attack from power source

4. Wait until the throwing wheels have come to a complete stop before

reaching hands or fingers anywhere near the throwing wheels.
CAUTION: Carefully check Crick Attack for completeness and condition before

connecting to electrical power:

1. Throwing wheels must be tight on the motor shafts

2. Wheel guard and ball chute must be tightly fastened to the throwing head.

Carefully check the throwing wheels frequently for cleanliness, chips and cracks. Do not

use the machine if the throwing wheels are damaged, or if chips or cracks appear in the

wheels. (For damage within Warranty period, see Warranty Statement, page i.)
ALWAYS set the speed controls to “0” before connecting the machine to power. Check

that the speed controls are at “0” before turning the on/off switch “ON”.
Do not allow anyone to walk in front of the machine if it is connected to electrical power.

WARNING

PERSONAL INJURY

HAZARD

Carefully read all instructions

in this manual, and all labels

and warnings on Crick Attack

before using this machine.
Use machine only under adult

supervision. Failure to operate

CrickAttack as described in

this manual can result in severe

personal injury or death.
Never loosen the horizontal

swivel lock while pitching to a

batter. If the lock is not secure,

the throwing head could pivot.
A loose swivel lock can allow a

pitch to be inside which could hit

the batter.

ELECTRICAL SHOCK

HAZARD

Crick Attack must be

connected to a properly

grounded electrical receptacle.

Do not operate on wet ground.

CAUTION

PERSONAL INJURY

HAZARD

Keep hands away from throwing

wheels anytime the machine is

connected to a power source.
Carefully check Crick Attack for

completeness and condition

before connecting to electrical

power.

EQUIPMENT

ELECTRICAL DAMAGE

Keep hands away from throwing

wheels anytime the machine is

connected to a power source.
Carefully check Crick Attack for

completeness and condition

before connecting to electrical

power.

«
...
2
3
4
5
6
...
»

Содержание CRICK ATTACK


















Отзывы:

Нет отзывов