manualshive.com logo in svg

Sports Attack CRICK ATTACK, Инструкция по эксплуатации, Страница: 12 / 17

Поделиться
Скачать
Sports Attack CRICK ATTACK Скачать руководство пользователя страница 12

CRICK ATTACK™ CRICKET BOWLING MACHINE

Sports Attack, LLC. 

•

 800.717.4251 

•

 www.sportsattack.com

10

Shutting Do

wn

CRICKET 

SHUTTING DOWN

TURNING CRICK ATTACK  “OFF”

1.  Set each speed control dial to “0”.
2.  Turn the on/off switch “OFF”.
3.  Unplug Crick Attack from the power source.

PUTTING CRICK ATTACK AWAY

1.  Be absolutely sure that the throwing wheels have completely stopped turning.  
2.  See Figure 7 at right:
  

a. Turn the elevation adjustment counter-clockwise until the throwing head    

 

    is  all the way down against the elevation control nut.

 

b. Push and hold the travel lock all the way in.

 

c. Turn the elevation adjustment clockwise until the throwing head is held 

 

    tightly against the travel lock. Tighten just enough to secure the throwing    

 

    head. It is not necessary to over tighten.

3.  Using the rear leg as a handle, tip Crick Attack up and over onto the wheel guard.  
4.  Remove (unsocket) both front legs and store by inserting in the travel storage sockets. 
5.  See Figure 8 at right: 

Again, using the rear leg as a handle, tip Crick Attack back until machine can be  

comfortably rolled on the travel wheels. Crick Attack can now be rolled and  

maneuvered off of the field.

6.  To transport Crick Attack in a car, remove the throwing head:
 

a. Be sure the travel lock is engaged and the throwing head is tightly secured  

 

    to the yoke.

 

b. Loosen the horizontal swivel control. Turn it counter-clockwise until the    

 

    throwing head is free to li

ft out of the swivel.

 c. 

Lift the throwing head straight up and clear of the undercarriage.

 SUGGESTION:

 The throwing head, while awkward, can be carried for short    

 

distances by gripping the top section of the wheel guard and balancing the   

 

piece against your thighs as you walk.

 

d. To prevent damage in transport, rest the throwing head on the wheel  

 

 

    guard and yoke; motors should be down, and the control panel pointing up.

Figure 7

  Secure the Travel Lock

Figure 8

  Maneuvering

Storing Legs in Travel Socket

ELEVATION

CONTROL

LOCKING 

TAB ON 

THROWING 

HEAD

TRAVEL

LOCK

USE TRANSPORT 

LEG AS A HANDLE 

TO MANEUVER

Содержание CRICK ATTACK


















Отзывы:

Нет отзывов