manualshive.com logo in svg

Sports Attack CRICK ATTACK, Инструкция по эксплуатации, Страница: 13 / 17

Поделиться
Скачать
Sports Attack CRICK ATTACK Скачать руководство пользователя страница 13

CRICK ATTACK™ CRICKET BOWLING MACHINE

Sports Attack, LLC. 

•

 800.717.4251 

•

 www.sportsattack.com

11

CARE, CLEANING & MAINTENANCE

LUBRICATION

 

(once per season, or as required):

1.  Elevation Control 
 

a.  Apply fresh grease.

 

b. Reinstall, making sure that the tension spring is around the threads.  

 

    (See item 30, 30B and 31 on page 13).

2.  Travel Lock
3.  Apply a small amount of grease where the pin passes through the fitting. Make sure 

the travel lock operates freely.

4.  Horizontal Swivel Lock
 

a. Completely remove the horizontal swivel lock nut. Clean all old grease,    

 

     

    dirt, etc. from the threads.

 

b. Wipe the threads with a very small amount of fresh grease.

 

c. Reinstall.

THROWING WHEEL MOTORS

Motors are sealed and require no lubrication. 

Check bolts for tightness once a season. Tighten bolts securely, but do not over-tighten. 

See Figures 7 and 8 on page 11.

CLEANING THE THROWING WHEELS

The throwing wheels must be kept clean to maintain accuracy. Clean the wheels  

periodically to control the build-up of grass and dirt.

1.  Turn the on/off switch “OFF” and allow the wheels to come to a complete stop. 

Unplug Crick Attack from electric power.

Dampen a rag with soap and water. Turn the throwing wheel by hand and scrub the 

wheel until the build-up is removed. For very heavy build-up, a synthetic scouring pad, 

such as a Scotch-Brite® scouring pad, or medium sandpaper may be used sparingly. 

Acetone may be  

required to help loosen the build-up of dirt or ball residue.

EXAMINE THE MACHINE

Examine Crick Attack for condition and completeness before every use:
1.  For batting practice, be sure the horizontal swivel lock is secured.
2.  Throwing wheels must be tight on the motor shafts. Check that the keyway retaining 

bolts are tight.

3.  Wheel guard and ball chute must be securely fastened to the throwing head.

CAUTION 

PERSONAL INJURY 

HAZARD

Never attempt to clean the  

throwing wheels while they are 

turning. Rags or implements 

caught in spinning wheels can 

cause serious injury.
Unplug the machine before  

cleaning the wheels or  

performing any service.

CHEMICAL HAZARD

Acetone

 

Read and follow the directions 

and safety instructions on the 

acetone container.

FIRE HAZARD

Acetone

 

Acetone is flammable. Do not  

use acetone around a fire or 

flame. Do not use acetone near  

a running generator or other 

source of ignition.

Car

e & Cleaning

Содержание CRICK ATTACK


















Отзывы:

Нет отзывов