Spokey DEMI, Руководство пользователя

Страница: 10 / 52

9
PREPARATIONS
1. Before assembly make sure there is enough space.
2. Use the recommended tools.
3. Before assembly check if there are all the parts in the box.
It is recommended that product should be assembled by at least two people
to avoid injuries.
.
ASSEMBLY INSTRUCTIONS ( Drawings
– p.
45-48)
STEP 1 Fix the front stabilizer (3) and rear stabilizer (4) to the main frame
(1) with the pin (12), curved washer (13) and nut (14).
STEP 2: Connect the sensor wire (20) to the extension cable (18) and the
resistance cable (19) to the resistance control cable (17).
Fix the handlebar stem (2) to the main frame (1) with the Allen bolt (16) and
spring washer (56).
STEP 3:
A: Fix the left grip (6L) onto the long axis of the handlebar stem (2) with the
Phillips head screw (24), spring washer (52), flat washer (25), wave washer
(64), placing it on the spindle (27) .
B: Fix the connector with the pedal support (5L) to the crank (22) with the
pedal support screw (38L), wave washer (62), spring washer (41) and nylon
nut (42L).
C: Connect the left grip (6L) to the pedal support (5L) with the Phillips head
screw (30), flat washer (31) and nylon nut (32). Tighten the Phillips head
screw (24) (30) and nylon nut (42L). Put the end caps (23) (57) (43).
D: Fix the pedal support (5R), right grip (6R) to the crank (22) and the
handlebar stem (2) in the same way.
E: Fix the pedals (10L/R) to the pedal supports (5L/R) with the Phillips head
screw (33), flat washer (34) and nylon nut (35).
STEP 4:
A: Insert the pulse sensor wire (50) to the handlebar stem (2). Fix the elbow-
rest (8) onto the handlebar stem (2) with the Phillips head screw (51) of the
spring washer (52), and then fix the handlebar grip cover (53).
B: Fix the left and right grip (7L/R) to the left one (6L/R) with the pin (45),
curved washer (44) and acorn nut (58).
STEP 5: Connect the pulse sensor (50) and the resistance cable (18) with
the counter wires (9), then fix the counter (9) onto the counter support,
located on the upper part of the handlebar stem (2), with the Phillips head
screw (55) and flat washer (54).
Levelling, moving the device
Before you start exercising, it is recommended to verify whether the bike is
positioned correctly. Level the equipment with the knobs of the front
stabilizer. To transport the device, raise it carefully on its front wheels
(Figure
– p. 49) and move to another place, holding it on both sides.
Resistance adjustment
The Resistance adjustment function allows to change resistance on the
pedals. High resistance requires larger effort while pedalling, whereas the
low one decreases the effort. Force of resistance is regulated by a knob
placed on the handlebar post. In order to decrease resistance, adjustment
knob should be turned towards the “1“ number whereas so as to increase
resistance, the knob should be turned towards the “8” number.
In order to achieve a satisfying effect, resistance level should be set during
a training..
MAINTENANCE

Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.

Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.

The device should be kept in a dry place in order to protect it against
dampness and corrosion.

Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.

In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
should be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Batteries: 1.5V AAA (2 pieces), not supplied with the bicycle
Inserting batteries
1. Insert two batteries at the back of the counter.
2. Make sure that the batteries are correctly positioned.
3. If the display is unreadable or only some segments are visible, remove
the batteries and re-insert them.
4. After removing the batteries, all function values will
be reset.
METER
First start-up
Before the first start-up, make sure that all the cables have been connected
correctly and that the batteries have been inserted correctly.
The display will turn on once you press the button or when you start
pedaling.
HOW TO OPERATE THE BIKE METER