Spokey 920871, Руководство пользователя

Страница: 9 / 44

7
Handlebar position adjustment
The position of handlebars can be adjusted by turning the handwheel in a
counter-clockwise direction, and setting it in an appropriate position. Make sure to tighten the handwheel, so that the set position is well
secured.
Resistance adjustment
High resistance requires larger effort while pedalling, whereas the low one
decreases the effort. Force of resistance is regulated by a knob placed on
the main frame. In order to achieve a satisfying effect, resistance level should be set during
a training The load system is independent of speed.
MAINTENANCE

Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.

Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.

The device should be kept in a dry place in order to protect it against
dampness and corrosion.

Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.

In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
should be made by a qualified SPOKEY’s company employee.
COUNTER INSTRUCTIONS
POWER SUPPLY
Battery Spec: 3V CR2032 (1PC).
BATTERY INSTALLATION INSTRUCTION:
1. Install a new CR2032 battery by tilti ng the battery slightly to its side and
slide it in. (po) at upper side and negati ve(-) at down side) 2. For the battery clnauge, please gently holding the clip oo the side and
the battery will pup up.
3. Put the battery cover back
COUNTER
Switching on (picture 1, p. 38)
1. Installs 1 piece of CR2032 3V battery, then the screen will display as
following "Drawing A" and have
"Bi" sound at the same time.
After that, it goes to the next step to the main menu as "Drawing B".
2. Get access to the set-up mode of TIME/DISTANCE/CALORIES/ PULSE.
When you are in each set- up mode, for example in the time set-up mode,
time value is blinking, you can press "SET" button to adjust the value and
press "MODE" for confirmation. The set-up of DISTANCE, CALORIES,
PULSE is the same as TIME.
3. With any signal been transmitted into the monitor, the value of TIME,
DISTANCE, CALORIES start to count up as Drawing C. When there is
any function has been preset the target (TIME or DISTANCE or CALORIES), the function will be counting down from the preset to zero
while the training starts. Once the target is achieved to zero, the monitor
start to beep for 8 seconds, and the function will be counting up from zero
directly if the training is going. Press "MODE" button for confirmation and
skip to next set-up.
4. In SCAN mode shown as "Drawing C". TIME/DISTANCE/CALORIES/
PULSE/ (RPM/SPEED)
will skip to display in every 6 seconds. The order is as follows.
5. You can also press "MODE" button to select single function display
except RPM & SPEED function.
The RPM & SPEED function will switch display.
Waking up from the energy saving mode
1. Stop training for 4 minutes, the computer will enter to Sleep mode.
You may press any button to have the computer restart working, the original
value will retain. (If re-install batteries, the original value will remove.) 2. If the computer displays abnormally, please re-install battery and try
again.
BUTON FUNCTIONS
MODE/ RESET - To confirm all settings. / Press this button and hold for 2
seconds to reset all function figures.
SET - To set up the value of TIME, DISTANCE, CALORIES, PULSE. You
can hold the button to increase the value fast. (The computer has to be in
stop condition.)
DISPLAY FUNCTIONS
SCAN - Displays all function TIME>DISTANCE>CALORIES>
PULSE>RPM/SPEED in sequence.
RPM - Displays the pedaling Rotation Per Minute. The RPM and SPEED
will switch to another display in every 6 seconds after exercise starts.
SPEED - Displays the user's exercise speed.
TIME 1.You can press "SET" button to set target time between 0:00 to
99:00 for count down function.
2. It can be set up by the user or accumulated automatically for count up
function.
DISTANCE 1.Your can press "SET" button to set target distance
between 0.0 to 99.50 for count down function.
2. It can be set up by the user or accumulated automatically for count up
function. CALORIES: 1.You can press "SET" button to set target calories
between 0 to 9990 for count down
function.
2. It can be set up by the user or accumulated automatically for count up
function.
PULSE - Displays the user's pulse. User may set the target pulse. When
pulse value reaches to the target, the computer will alarm with "Bi" sound