background image

Spirent B2-800-QD-4-T1S Installation Instructions

Spirent B2-800-QD-4-T1S Installation Instructions

|

3

PN 71-009377  Rev A May 2022

right to change the warranty and service policy set forth above at any time, after 
reasonable notice and without liability to Customer.

TO THE EXTENT PERMITTED BY APPLICABLE LAW, ALL IMPLIED 
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF 
MERCHANTABILITY, NONINFRINGEMENT AND FITNESS FOR A PARTICULAR 
PURPOSE, ARE HEREBY EXCLUDED, AND THE LIABILITY OF SPIRENT, IF 
ANY, FOR DAMAGE RELATING TO ANY ALLEGEDLY DEFECTIVE PRODUCT 
SHALL BE LIMITED TO THE ACTUAL PRICE PAID BY THE CUSTOMER FOR 
SUCH PRODUCT. THE PROVISIONS SET FORTH ABOVE STATE SPIRENT'S 
ENTIRE RESPONSIBILITY AND CUSTOMER'S SOLE AND EXCLUSIVE REMEDY 
WITH RESPECT TO ANY BREACH OF ANY WARRANTY.

Safety Precautions

Warning

:

 Calls attention to operating procedures or practices that should be followed to 

avoid bodily injury or damage to equipment.

Caution

Reflects conditions that could cause product damage or data loss.

Note

Describes limitations on the use of the equipment or procedure.

Children Warning

Warning:  

This equipment is not suitable for use in locations where children are likely to 

be present.

Waarschuwing

: Deze apparatuur is niet geschikt voor gebruik op locaties waar kinderen 

waarschijnlijk aanwezig zijn.

Attention

: Cet équipement n'est pas adapté à une utilisation dans des endroits où des 

enfants sont susceptibles d'être présents.

No User-Serviceable Parts

Warning:  

No user-serviceable parts inside. Do not open.

Waarschuwing:  

Er zijn geen door de gebruiker te vervangen onderdelen. Niet openen.

Attention:  

Aucune pièce se trouvant à l'intérieur ne peut être réparée ou remplacée par 

l'utilisateur. Ne pas ouvrir.

Lasers Warning

Warning:  

Because invisible radiation may be emitted from the aperture of the port when 

no fiber cable is connected, avoid exposure to radiation and do not stare into 
open apertures.

Waarschuwing:  

Aangezien onzichtbare straling vanuit de opening van de poort kan 

komen als er geen fiberkabel aangesloten is, dient blootstelling aan straling en het kijken 
in open openingen vermeden te worden.

Содержание B2-800-QD-4-T1S























Отзывы: