Spirax Sarco LC2250 Скачать руководство пользователя страница 1

Страница: 1 / 44

IM-P402-130

EMM Issue 9

Commissioning password

Current legislation states that in order to prevent tampering and potentially hazardous

programming errors, access to the pass codes required to enter commissioning mode

should only be available to qualified and trained personnel.

Enter commissioning

To enter the commissioning mode, press and hold the

button for 5 seconds.

The display will show the pass code '888'. Enter the pass code '745'. This is fixed and cannot

be changed.

If an incorrect pass code is entered, the display will return to showing the current valve / pump

status – run mode.

If the correct pass code is entered, the display will show the main menu structure. Select

'End' to leave the menu.

Once in the commissioning mode press the button:

to scroll through the menus.

to increase digits when in a menu.

Press the

button to enter a menu choice (select a parameter or digit) and shift right, onto

the next digit.

This page MUST be removed after

commissioning and kept in a safe,

access controlled location.

Printed in GB

IM-P402-130

EMM Issue 9

4025251/9

LC2250

Level Controller

Installation and Maintenance Instructions

1. Safety information
2. User instructions and

delivery information

3.  System overview
4.  Mechanical installation
5.  Electrical installation
6.  Commissioning

- Quick set-up
- Full

7. Communications
8. Maintenance
9.

Fault finding

10. Technical information

- Default settings

11. Appendix

- Data registers

12. Menu map

LC2250

Содержание LC2250













































Результаты поиска

Содержание LC2250

Отзывы:

Похожие инструкции для LC2250

Бренды по названию

Популярные бренды

Spirax Sarco LC2250, Инструкция по установке и обслуживанию

Результаты поиска

Содержание LC2250

Отзывы:

Похожие инструкции для LC2250

Бренды по названию

Популярные бренды