background image

22

Console Care

Precor strongly recommends performing regular maintenance to ensure the 

console performs accurately. 

Important  

It is the duty of the owner to maintain equipment in accordance with 

the instructions in this material and any accompanying material. Always purchase 

replacement parts and hardware from Precor. If you use parts not approved by 

Precor, you could void the Precor Limited Warranty. Use of parts not approved by 

Precor may cause injury.

Follow these recommended procedures:

Daily:

•  After each use, wipe down the console using a soft cloth moistened 

with a mild soap solution in a 30:1 water-to-cleaner ratio. Spray the 

solution onto a soft cloth and then wipe the console.

•  Never spray liquids directly onto the console or use abrasive cloths, 

oil, ammonia, or alcohol-based cleaners.

Weekly:

•  Inspect each console for loose parts, bolts and nuts, adjust and 

tighten loose hardware as needed.

•  Remove any consoles that are damaged, not properly mounted, or  

at risk of coming loose.

Monthly:

•  Inspect all parts for damage and replace parts as required.

•  Inspect mounting of the cadence sensor and magnet to ensure it is 

intact and working properly.

•  A “low battery” indicator displays when batteries need replacing. 

Replace the batteries in the console with 3 high-quality AAA alkaline 

batteries.

Содержание Studio Console





























Отзывы: