Sperry Marine 5016-CA Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 132

background image

056376-A

Analogue Compass Repeaters

4-2

Maintenance by Shipboard Personnel

Maintenance of externally installed Bearing Repeater

Of course, depending on whether the compass repeater is installed
externally or internally, the cleaning effort may vary and will be
increased with exposition to environmental conditions, e.g. when
installed on the fly bridge or top desk.

Especially the bearing repeater installed on a bearing stand is perma-
nently exposed to environmental conditions and does therefore need
additional protection for long time usage and for reduction of unneces-
sary wear.

It is therefore recommended to always protect the bearing repeater with
the cover plate against solar radiation when not in use.

Additionally, the usage of the watertight plastic cover for protection
against all environmental conditions is also recommended when the
bearing repeater is not in use.

CAUTION

Risk of damage though solar radiation
The bearing repeater 5016-CA is equipped with a cover plate for protec-
tion against solar radiation.
It is recommended to always protect the bearing repeater with the cover
plate when not in use.

CAUTION

Risk of damage
The cover plate, protecting the bearing repeater 5016-CA against solar
radiation, must never be touched with tools to avoid any damage.
Always install and remove the cover plate with bare hands only.

CAUTION

Risk of unnecessary wear
The bearing repeater 5016-CA can optionally be equipped with a water-
tight plastic cover for protection against environmental conditions.
It is recommended to always protect the bearing repeater with the plastic
cover when not in use.

«
...
38
39
40
41
42
...
»

Содержание 5016-CA





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5016-CA

Бренд: Zibro Страницы: 16

Бренд: NARVI Страницы: 48

Бренд: Fabbri Termomeccanica Страницы: 35

Бренд: Icom Страницы: 56

Бренд: Icom Страницы: 16

Бренд: Cantherm Страницы: 11

Бренд: Jaga Страницы: 2

Бренд: B&B Electronics Страницы: 2

Safe-T FURNACE HC-445

Бренд: Pelonis Страницы: 6

New XR Designer

Бренд: Haverland Страницы: 8

RADSON MIED0508EL

Бренд: Purmo Страницы: 32

Бренд: MV Heating Страницы: 19

SingleHeater SH 312 Series

Бренд: IRT Страницы: 20

Бренд: TaoTronics Страницы: 13

Бренд: Lorell Страницы: 14

Бренд: DSC Страницы: 10

Бренд: S+H Nolting Страницы: 34

Бренд: COMBA Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды