k^sfd^q u jh N
MRSPQPLc
fåáíá~ä=póëíÉã=`çåÑáÖìê~íáçå
TJT
TKR fåáíá~ä=póëíÉã=`çåÑáÖìê~íáçå
To make the system fully functional, the configuration parameters need
to be set to the required values in the Service Setup 1, see “Configura-
tion Menu - Service Setup 1” on page 8-1.
Additionally, the applicable standard operational settings should be
entered in the Manual Settings menu.
If a magnetic compass heading source is connected to the
NAVIGAT X MK 1 system, the magnetic compass calibration procedure
should be carried out during a sea trial, as described under ”Magnetic
Compass Calibration” on page 7-10.
`çåÑáÖìê~íáçå=çÑ=íÜÉ=póëíÉã
1. Check that the wiring has been carried out completely. All devices
connected to data or signal in- and outputs should be operative.
2. Energize the system at the vessel's switch and fuse unit.
A startup message is displayed and the initial self test is executed.
3. Go to the ”Configuration Menu - Service Setup 1” on page 8-1.
4. Select the required system type and heading reference selection set-
tings.
5. In dual or triple gyro systems, assign the required compass ID.
6. Select the required data formats for all devices connected to the data
inputs. In G or GG type systems, disable the magnetic compass
heading input, in G or GM type systems, disable the ext. gyro input.
7. Select the required data output formats and IEC 61162/NMEA proto-
col standard setting.
8. Check that the min./max. limits for the speed filter are well outside
the possible range of the vessel’s operating speed. In high-speed
craft, the max. speed value will have to be increased.
9. If required, set the parameters for the analogue rate of turn output,
the status in- and outputs and the rudder angle feedback inputs.
a^kdbo
iáÑÉ=Ç~åÖÉê=íÜêçìÖÜ=ÉäÉÅíêáÅ~ä=ëÜçÅâ
tÜÉå=íÜÉ=Åçãé~ëë=áë=ÉåÉêÖáòÉÇI=íÜÉ=ÖóêçëéÜÉêÉ=çéÉê~íáåÖ=îçäí~ÖÉ=çÑ=
NMM=s^`=]=PPT=eò=áë=éêÉëÉåí=çå=íÜÉ=ã~ëíÉê=m`_I=íÜÉ=ÖóêçëéÜÉêÉ=ëìééäó=
äáåÉë=~åÇ=~Åêçëë=íÜÉ=ÖóêçëéÜÉêÉ=Åçåí~ÅíëK=
tÜÉå=íÜÉ=^`=ã~áå=ëìééäó=áë=ëïáíÅÜÉÇ=çåI=Ü~ò~êÇçìë=äáÑÉ=îçäí~ÖÉë=~êÉ=
éêÉëÉåí=~í=íÜÉ=äáåÉ=ÑáäíÉê=~åÇ=íÜÉ=éçïÉê=íê~åëÑçêãÉêÛë=íÉêãáå~äëK
_É=ÉñíêÉãÉäó=Å~êÉÑìä=ïÜÉå=çéÉê~íáåÖ=íÜÉ=Åçãé~ëë=ïÜáäÉ=íÜÉ=ÜçìëáåÖ=áë=
çéÉåK=aç=åçí=íçìÅÜ=íÜÉ=ã~ëíÉê=m`_I=íÜÉ=ÅçååÉÅíáåÖ=Å~ÄäÉë=íç=íÜÉ=ÖóêçJ
ëéÜÉêÉ=Åçåí~áåÉê=çê=~åó=çíÜÉê=ÅçåÇìÅíáîÉ=ÅçãéçåÉåíë=çå=íÜÉ=Åçåí~áåÉê=
çê=áå=íÜÉ=Åçãé~ëë=ÜçìëáåÖK
^äï~óë=ÉñÅäìÇÉ=~åó=Åçåí~Åí=íç=ÉåÉêÖáòÉÇ=ÅçãéçåÉåíëK
kçíÉ
If the initial system configuration is carried out before the installation of
the gyrosphere, the system will raise a „gyro failure“ alarm at power-up.
The alarm may be safely acknowledged at this point to continue with the
initial configuration.
Содержание 4914-CA
