background image

10

Sperry Instruments

800-645-5398

Menomonee Falls, WI 53051

sperryinstruments.com

SPR_TL_066_1017

SPERRY INSTRUMENTS LIMITED LIFETIME WARRANTY

Subject to the exclusions and limitations detailed below, Sperry Instruments provides a limited lifetime warranty on products  

of its manufacture will be free from defects in materials and workmanship under normal use and service.

Limited

Limited means that Sperry Instruments warrants to the original purchasers of products from Sperry Instruments authorized 

distributors at the time of shipment such products shall be free of defects in material and workmanship while the tool is used 

under normal working conditions. Standard wear and tear, dulling over time, overloading, misuse, and acts of God are not 

covered under warranty. This warranty does not cover batteries, fuses, or test leads.

When a warranty claim arises, the purchaser must contact Sperry Instruments. If the defect comes under the terms of this  

limited warranty, Sperry Instruments will arrange, at its sole discretion, one of the following options: 

• Product will be replaced

The purchaser is solely responsible for determining the suitability of Sperry products for the purchaser’s use or resale, or 

for incorporating them into articles or using them in the purchaser’s applications. The distributor is authorized to extend the 

foregoing limited warranty to its original purchasers in connection with the sales of Sperry products, provided that such products 

shall not have been altered by the distributor. The distributor shall be fully responsible for any warranties the distributor makes to 

its purchasers which are broader or more extensive than Sperry’s limited warranty. 

Lifetime Warranty

Warranty Limitation: The forgoing warranties are exclusive and are in lieu of all other express and implied warranties whatsoever, 

including but not limited to implied warranties of merchantability and fitness for a particular purpose. The foregoing warranties 

do not cover ordinary wear and tear, abuse, misuse, overloading, alterations, products which have not been installed, operated 

or maintained in accordance with Sperry’s written instructions. Test leads, fuses, batteries and calibration are not covered under 

any implied warranty. “Lifetime” of products that are no longer offered by Sperry will be either repaired or replaced with an item 

of Sperry Instruments choice of similar value. Lifetime is defined as 5 years after Sperry discontinued manufacturing the product, 

but the warranty period shall be at least ten years from date of purchase. Original proof of purchase is required to establish 

original ownership of product.

No warranty will be honored unless an invoice or other proof of purchase date is provided to Sperry Instruments. Hand written 

receipts or invoices will not be honored. 

©2016 Product Power, LLC All rights reserved.

- See more at: http://www.sperryinstruments.com/en/resources/warranty-page#sthash.4sNKZu3b.dpuf

Содержание DM6650T











Отзывы: