Spencer Carrera Tec, Руководство пользователя, Страница: 18 / 22

13
Lifting the stretcher
To bring back the stretcher back to the standard height, starting from any of the previous configurations, the operators must coordinate
while simultaneously lifting the front and rear of the stretcher, ensuring the proper alignment of the patient bed. Do not carry out these
operations until you have checked that the patient has been properly restrained with the strap and that the sidebars are raised.
At the rear, grab the part of the frame near the footrest of the patient bed or the telescopic handles if the stretcher is equipped with them.
At the front, similarly grab the frame above the loading trolley or the telescopic handles if the stretcher is equipped with them.
Raise the assembly until the locking mechanisms are properly engaged.
Only use the frame or the telescopic handles for lifting.
Do not use the boards or other areas that are not designed for this purpose.
11.10 Telescopic handle operation - Image P26
Carrera Tec TH is equipped with telescopic handles that allow it to be lifted over small obstacles, temporarily avoiding the transmission of
stress from the ground to the patient.
• To pull out the telescopic handles, press the red button on the top and pull the handles out slightly. After a stroke of about 2cm,
release the buttons and pull the handles until the next locked position is reached, which will lock automatically.
• When the locked position is reached, check that it is secure by trying to retract the handles without operating the release buttons.
To close the handles back up, press the unlock buttons and bring the handles to their original position.
11.11 Lifting the stretcher with the patient
•
Secure the patient to the stretcher with the straps provided, adjusting the tension correctly according to the patient's clinical condition.
•
The operators must stand at the ends of the stretcher (one at the feet and one at the head)
•
Using an adequate lifting technique to avoid fatigue, operators must grab firmly at both ends. Raise the stretcher.
11.12 Spine board housing (Carrera Pro only) - Image 27
•
Brake the stretcher (see paragraph 4.3.9), place the spine board with the foot end facing the stretcher housing on the control side (fig. G)
and insert it fully into the end stop on the head end tube of the stretcher frame.
•
To remove the stretcher, brake the stretcher, grab it from the underside of the Carrera Pro frame to avoid injury to the operator's hands,
and pull it out completely without knocking the spine board to the ground.
•
Take care during insertion and removal not to cause injury to the patient or the operator by applying excessive force on the device.
12. CLEANING AND MAINTENANCE
Spencer Italia S.r.l. declines all responsibility for any direct or indirect damage which is the consequence of improper use of the product
and spare parts and/or in any case of any repair carried out by a person other than the Manufacturer, who uses internal and external
technicians authorised to do so; moreover, doing so will invalidate the warranty.
•
The operator must wear suitable personal protective equipment, such as gloves, goggles, etc. during all checking, maintenance and
cleaning operations.
•
Establish a maintenance schedule, periodic inspections and extend the average life span, if foreseen by the Manufacturer in the User
Manual, identifying a reference person who meets the basic requirements set forth in the User Manual.
•
The frequency of inspections is determined by factors such as legal requirements, type of use, frequency of use, and environmental
conditions during use and storage.
•
Repairs of products manufactured by Spencer Italia S.r.l. must be carried out by the Manufacturer, who shall make use of specialised
internal or external technicians who, using original spare parts, shall provide quality repair service in strict compliance with the
technical specifications indicated by the Manufacturer. Spencer Italia S.r.l. declines any responsibility for any direct or indirect damage
which is a consequence of improper use of spare parts and/or any repair work carried out by unauthorised parties.
•
Use only original or Spencer Italia S.r.l. approved components/spare parts and/or accessories in order to carry out all operations without
causing alterations or modifications to the product.
•
All maintenance and overhaul activities must be recorded and documented with the relevant technical operation reports. This
documentation must be kept for at least 10 years after the end of the product's life and must be made available to the competent
authorities and/or the Manufacturer when requested.
•
Cleaning, provided for reusable products, must be carried out in accordance with the Manufacturer's instructions in the User Manual in
order to avoid the risk of cross-infection due to the presence of body fluids and/or residues.
•
The product and all its components must be washed and left to dry completely before storage.
•
If the product requires lubrication, this must be done after cleaning and complete drying.
•
The dedicated stretcher fixing system is equipped with a system that signals the need for stretcher maintenance and of the fixing itself
linked to the cycles of use. Strictly observe the required maintenance intervals.
•
Document maintenance using the form in Annex B of this manual or other appropriate forms.