manualshive.com logo in svg

Spektrum FC6250HX, Руководство пользователя

Поделиться
Скачать
Spektrum FC6250HX Скачать руководство пользователя страница 13

EN

13

Bubble Level

Foam Blade 

Holder

Binding with Optional Second Remote Receiver

1.  Remove the telemetry remote cable from the BND/PRG/RX2 port.
2.  Insert a bind plug into the BND/PRG/RX2 port.
3.  Power ON the FC6250HX, the orange LED on the remote receiver will 

begin to flash to indicate it is in bind mode. 

4.  Leave power connected and remove the bind plug.
5.  Reconnect the telemetry remote cable to the BND/PRG/RX2 port and press 

the bind button on the telemetry remote receiver. The orange LED on the 

telemetry remote will flash when it enters bind mode. Release the bind 

button.

6.  Put your transmitter into bind mode. The Orange LED on the remotes will 

remain lit when the bind is successful. 

Repeat the process if necessary.

1. Level the model using a bubble level on the roll and pitch axis, power on and 

initialize the system.

2. Go to the 

System Setup

 menu and select 

Calibrate

. 

3. Select 

Apply

. 

A red flashing light during calibration indicates the model is either not level 

or not stationary. Level the model, taking care to keep it still.  

A yellow flashing light during calibration indicates the calibration is 

proceeding normally.

4. After the calibration is successful, the LED flashes green. 

Содержание FC6250HX





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды