Spectrum WaterScout SMEC 300 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 24

Spectrum WaterScout SMEC 300 Скачать руководство пользователя страница 10

10

The EC sensor can be checked with the 1.41 mS/cm cali-
bration standard (see Calibrating the EC Sensor p.

9

).

The soil moisture calibrations were developed using min-
eral soils and a soilless material (peat moss). Therefore the
sensor will not give a value of 100% in water. To check if
the soil moisture sensor is still functioning properly, read-
ings can be taken in the following media:

Air
In air, the sensor should read a VWC of 0%.

Water
In distilled water, the sensor should read a VWC of about
55% in Standard mode and about 68% in Soilless mode.

Saturated Playground Sand
Add water to playground sand until the surface glistens
and no additional water can permeate the sand. The sen-
sor should read a VWC of about 29% in Standard mode
and about 60% in Soilless mode.

Note: WatchDog weather stations display the Standard
VWC value. The soilless mode is available on the
handheld reader only.

Checking the Sensor

«
...
8
9
10
11
12
...
»

Содержание WaterScout SMEC 300

























Отзывы:

Нет отзывов