Spectrasensors SS1000 Скачать руководство пользователя страница 63

Страница: 63 / 83

Troubleshooting

–

Tighten all new compression fittings 1-1/4 turns with a wrench from

finger tight. For connections with previously swaged ferrules, thread

the nut to the previously pulled up position, then tighten slightly with

a wrench. Secure tubing to appropriate structural supports as

required.

Check all connections for gas leaks. SpectraSensors recommends

using a liquid leak detector.

Cleaning the Mirrors

If contamination makes its way into the cell and accumulates on the internal

optics, a

Power Fail

will result. If mirror contamination is suspected, please

consult with your factory sales representative before attempting to clean the

mirrors. If advised to do so, use the following procedure.

Tools and Supplies:

•

Lens cleaning cloth (Cole Parmer

EW-33677-00 TEXWIPE

Alphawipe

Low-Particulate Clean Room Wipes or equivalent)

•

Reagent-grade isopropanol (ColeParmer

EW-88361-80 or

equivalent)

•

Small drop dispenser bottle (Nalgene

2414 FEP Drop Dispenser

Bottle or equivalent)

•

Acetone-impenetrable gloves (North NOR CE412W Nitrile Chemsoft™

CE Cleanroom Gloves or equivalent)

•

Hemostat (Fisherbrand™ 13-812-24 Rochester-Pean Serrated

Forceps)

•

Bulb blower or dry compressed air/nitrogen

•

Torque wrench

Do not attempt to clean the cell mirror until you have consulted

with your factory service representative and have been advised to

do so.

The sample cell assembly contains a low-power, 10 mW MAX, CW

Class IIIb invisible laser with a wavelength between 700-

3000 nm. Never open the sample cell flanges or the optical

assembly unless the power is turned off.

Always handle the optical assembly by the edge of the mount.

Never touch the coated surfaces of the mirror.

UK Distibution by IMA Ltd

Tel: +44 (0)1943 878877 Email: [email protected] Web: www.ima.co.uk

Содержание SS1000




















































































Результаты поиска

Содержание SS1000

Отзывы:

Бренды по названию

Популярные бренды

Spectrasensors SS1000, Руководство оператора

Результаты поиска

Содержание SS1000

Отзывы:

Бренды по названию

Популярные бренды