Spectrasensors SS1000 Скачать руководство пользователя страница 21

Страница: 21 / 83

SS1000 Operator’s Manual

–

2 - I

NSTALLATION

Installing the analyzer is relatively easy requiring only a few steps that, when

carefully followed, will ensure proper mounting and connection. Once the

analyzer arrives, you should take a few minutes to examine the contents before

installing the unit.

What Should be Included in the Shipping Box

The contents of the box should include:

•

The SpectraSensors SS1000

•

This Operator’s Manual with instructions on setting up and operating

the analyzer

•

Carrying case

•

Membrane separator filter (installed)

•

100

–

250 VAC, 50/60 Hz battery charger

•

Quick-connect fittings for inlet and outlet tubes

•

One external serial cable to connect the analyzer to a computer

•

Additional accessories or options as ordered.

If any of these contents are missing, contact your sales representative.

Inspecting the Analyzer

Unpack and place the unit on a flat surface. Carefully inspect all enclosures for

dents, dings, or general damage. Inspect the inlet and outlet connections for

damage, such as bent tubing. Report any damage to the carrier.

Hardware and Tools for Installation

Depending on the particular model, the configuration of accessories and

options ordered, you may need the following hardware and tools to complete

the installation process.

Hardware:

•

Heated pressure regulator (if inlet pressure is >10 psig or no probe

regulator exists)

Avoid jolting the instrument by dropping it or banging it against a

hard surface. Do not attempt to pick up the instrument using the

sample cell. Either action may disturb the optical alignment.

UK Distibution by IMA Ltd

Tel: +44 (0)1943 878877 Email: [email protected] Web: www.ima.co.uk

Содержание SS1000




















































































Результаты поиска

Содержание SS1000

Отзывы:

Бренды по названию

Популярные бренды

Spectrasensors SS1000, Руководство оператора

Результаты поиска

Содержание SS1000

Отзывы:

Бренды по названию

Популярные бренды