1. Important Safety Instructions
A.
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING
!
2. Introduction and Planning
!
WARNING
!
WARNING
!
WARNING
!
WARNING
3
When installing and using this electrical equipment,
basic safety precautions should always be
followed, including the following:
B. : To reduce the risk of injury, do not
permit children to use this equipment unless they
are closely supervised at all times. Failure to
adhere to this and all other warnings could result in
serious injury or death.
C. A licensed electrician is required for all wiring
connections.
D.
TO REDUCE RISK OF ELECTRICAL
SHOCK,
connect all ground wires to grounding
terminal located in the control box. Use no smaller
than a No. 12 AWG (3.3 mm
2
) wire.
E.
TO REDUCE RISK OF ELECTRICAL
SHOCK,
a bonding connector is provided on the
motor for bonding of local ground points such as
water pipes, metal ladders/handrails, or other
metal within 5 feet of the pool. All local ground
points should be bonded with a No. 8 AWG (8.4
mm
2
) wire. Never use gas piping as an electrical
ground.
F. All electrical equipment should be installed in
accordance with local codes.
The
B
ADU
S
TREAM
II
has no protruding parts,
ensuring the pool user's safety. It is very compact
and installs at minimal cost.
The
B
ADU
S
TREAM
II
is normally incorporated
into the original pool design. However, it can be
added to any pool at a later date.
The
B
ADU
S
TREAM
II
can be installed in any
size pool. We suggest a minimum pool size of
7 ft. wide, 14 ft. long and 3 1/2 ft. deep in
order to swim. Most prefer 16 ft. in length or
longer. The extra length allows the swimmer to
comfortably drift back and swim up stream. The
B
ADU
S
TREAM
II
is complete with jet housing,
4 HP or 3.5 HP pump, control box, and
optional massage hose. The only additional
requirement is the plumbing. (4" pipe for 4 HP
and 3" pipe for 3 HP units.)
G.
DO NOT
store or use gasoline or other
flammable vapors or liquids in the vicinity of this
equipment.
DO NOT
store pool chemicals near the
equipment.
H.
DO NOT
remove any safety alert labels such
as
DANGER,
WARNING,
or
CAUTION
. Keep
safety alert labels in good condition and replace
missing or damaged labels.
I. Keep and read all equipment manuals. Adhere
to all of their instructions.
J. : Stay alert, watch what you are doing
and use common sense.
DO NOT
use unit if you
are tired and/or exhausted.
DO NOT
use unit while
under the influence of drugs, alcohol, or any
medications.
exercising with the
B
ADU
S
TREAM
II
or using the
massage hose.
K. : Consult your physician before
B
ADU
S
TREAM
II
if the square, anti-entrapment
cover is missing, broken or loose.
L. :
DO NOT
use or operate the
M.
SAVE THESE INSTRUCTIONS!
Refer to them
frequently and use them to instruct third party
users.
Consult local codes for minimum distance between
pump and pool. Locate pump as close to the
B
ADU
S
TREAM
II
as practical.
Use at least 4" pipe when distance between jet
housing and pump is 30 ft. or less and 6" pipe
for runs longer than 30 ft.
The 4 HP, self-priming, plastic pump has a
single phase motor with thermal overload (no
motor starter required). The 4 HP single phase
motor draws a maximum of 19.4 amps @ 230 V.
The unit requires a minimum circuit of 30 amps.
Install a 40 amp breaker to avoid nuisance
tripping when the pump is turned on and off
frequently. The starting current of the 4 HP
motor can reach up to 6 times the running
currents. (Three phase motor draws a maximum
of 12.8 amps @ 230 V and 6.4 amps @ 460 V.)
The 3.5 HP single phase motor draws 13.6
amps @ 230 V.
