10. Frequently Asked Questions
8. Operation Instructions
!
WARNING
9. Winterizing
10
Remove red filler plug or stainer tank lid on pump and
fill pump with water. Replace red filler plug or lid.
Push pneumatic button on. For the first start-up allow
approximately 5 minutes for the pump to prime. If the
pump has not started priming after 5 minutes, the
amount of water in the pump was not sufficient. Add
more water.
To start swimming, jogging or running it is suggested
that the two nozzles are pointed slightly inward and
slightly upward so that the water "breaks"
approximately 3ft. in front of the
B
ADU
S
TREAM
II
Start swimming with only minimal force in arms and
legs until you feel yourself drifting backwards, then
add force and swim upstream until a proper balance
is found between force and endurance.
Keep in mind that this unit is designed for a balanced
workout. Find a pace that you can keep up for at least
20 minutes. Out pacing is always possible. The idea
is to continue exercise for an extended period of time.
Consult your physician before attempting any
strenuous exercise. This product may not be
challenging or satisfying for all levels of exercise.
The air regulator permits a controlled mixture of air
into the water flow and creates a unique, invigorating,
bubble bath effect. It will also add additional
resistance to swim against.
B
ADU
S
TREAM
II
's adjustable flow nozzle enables
swimmer to regulate the volume of water released
through the jet(s). Turning the nozzle clockwise
reduces the flow.
The swivel nozzle(s) of the
B
ADU
S
TREAM
II
can
be positioned in various directions, allowing
swimmers to use various swim styles.
OPTION:
A pulsating massage hose can be attached
to one of the nozzles for massages. (Ask your dealer
for availability.) Use massage hose as advised by
your physician.
Directions for use: Consult your physician before
using the massage hose. To reduce the risk of injury,
do not permit children to use the massage hose with
pulsator unless they are closely supervised at all
times. Close air regulator. Reduce the volume of
water by turning the adjustable flow nozzle(s)
clockwise.
Under certain conditions it is possible that the current
"drifts off" the the left or the right from the middle due
to water bouncing off the back wall. In the event that it
interferes with your swimming action, turn unit off for
a few minutes and restart.
Do not use or operate the
B
ADU
S
TREAM
II
if the square, anti-entrapment cover is missing, broken,
or loose.
In areas subject to freezing water temperatures, protect
pump by removing drain plug and red filler plug (or lid).
Drain pool until water level has dropped below the square,
anti-entrapment cover. Alternatively purchase a winter
cover kit part # 2308752006K.
What size pool do I need?
The
B
ADU
S
TREAM
II
can be installed in any size pool. However, we
recommend a minimum length of 14' and a minimum
width of a swimming lane.
What size plumbing is necessary?
How far away
from the
B
ADU
S
TREAM
II
can the pump be installed?
Use a 4" plumbing up to 30'. For runs longer than 30'
use 6" plumbing. The pump can be placed as close to
B
ADU
S
TREAM
II
as local codes will allow.
How many amps does the pump operate at?
4 HP: Maximum 19.4 amps @ 230 V
3.5 HP: Maximum 13.6 amps @ 230 V
What size breaker do I need?
You must use a 40
amp breaker for the 4 HP pump or 30 amp breaker for
the 3 HP pump to avoid nuisance tripping.
Does it matter if the housing is installed higher or
lower than the manual states?
Yes, the center of
the jet must be 10" BELOW estimated water level for
proper performance of unit.
Can the air regulator be placed elsewhere?
Yes,
as long as it is not continuously flooded with water.
Can the pump be placed below water level?
Yes.
However, for best performance we recommend
ordering pump for flooded suction (Model 21-80/33G)
instead of self-priming (Model 21-80/33 GS). We
recommend installing valves for ease of maintenance.
How far away can the air button function
properly?
A maximum of 50'. Consult factory for
distances over 50'.
Do I need to install a motor starter?
No the pump
has a built-in thermal overload.
