manualshive.com logo in svg
background image

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION, OPERATING AND SERVICE MANUAL

READ AND FOLLOW ALL INSTRUCTIONS

This is the

II

All parts are manufactured of corrosion-resistant material and combined in one single
housing (or two single housings for two jet systems) which can be installed in pools of
any size and shape.

Key to illustration:

A. Flush mounted Jet Housing.

B. Square, Anti-Entrapment Cover (8 1/4" x 8 1/4")
undetectable pump suction. (Optional Round)

C. Adjustable Water Flow Jet Nozzle.

D. Air Regulator adjusts amount of air bubbles in
water flow.

E. Control Box with GFCI with pneumatic button
and tubing.

G. Optional Massage Hose with pulsator may be
attached to jet nozzle.

Counterstream Swimming Unit

U.S. Patent No. 3.977.027

OWNER'S MANUAL

The Speck

II

Complies with UL 1563

Swimming Pool Equipment
Listing #E212148

F. Speck 4 HP or 3.5 HP self-priming, plastic
pump, single phase with thermal overload (no
motor starter required). Optional three phase
motor and control available (Normal priming
pump available for installation below water level).

II

®

®

®

D

B

C

A

G

F

E

Содержание BADUSTREAM II













Отзывы: