background image

6

M017837080000 REV. January 19, 2011

2EZ Speed

TM

 Pool Motor with Programmable Control/Timer

M017837080000 REV. January 19, 2011

7

2EZ Speed

TM

 Pool Motor with Programmable Control/Timer

user Interface Identi cation

This section describes the motor’s user interface. 

run/SToP

 button. This button is used to activate or stop the unit operation. The button 

will be not be lit when power is applied to the user interface while in STOP mode and 

will be illuminated if in the run mode. 

  NOTICE

!

This button does 

noT

 disconnect 

power to the unit.

Press the 

EnTEr

 button to confirm and save your selections. Use the 

 

 arrow keys 

for menu navigation purposes and the 

 

 keys for changing values. For example, while 

changing the time, 

 

 keys will move you from the hours to the minute’s field, while 

the 

 

 keys will change the hour from 10 to 11 etc.

High Speed override

 – Runs the motor on high speed and sets countdown timer for 

60 minutes and will begin counting down. Pressing the button again will end override.

Low Speed override

 – Runs the motor on low speed and sets countdown timer for 

60 minutes and will begin counting down. Pressing the button again will end override.

1

2

3

4

General Installation Instructions

Follow these instructions to prolong the life of your 

swimming pool pump motor/control.

 

a.

  Protection against Heat

    •  Shade the motor/control from the sun.
    •  Provide ample cross ventilation.
    •   Protect the motor/control from lint, etc.,  

that can plug the ventilation openings.

 

b.

  Protection against Dirt

    •   Keep motor/control and surrounding area clean.
    •   Avoid sweeping or stirring dust near the motor/

control while it is running.

    •   Avoid storing or spilling dry chemicals near  

the motor/control.

 

c.

   Protection against Moisture

    •   Shade the motor/control from rain, snow, etc.
    •    Do not wrap motor/control with plastic or other  

air tight materials.

    •    Locate motor/control on a slight elevation so water 

will not run or puddle nearby.

    •   Avoid splashing water on or near the motor/control.
    •    Contact qualified service person to repair leaky  

pipe joints or pump seals promptly.

Basic Motor/Timer operation

WARNING

!

 

A properly  un tionin  motor may 

e too hot to tou h and  ause in ury

 Be careful when 

touching the exterior of an operating motor! This condition 

is normal for most motors when operated at rated load  

and voltage.

Your 2EZ Speed

TM

 motor/timer has been fully tested for 

pool pump use before shipment. It is designed to be a 

drop-in replacement for a standard single or two-speed 

pool pump motor with only minor programming required. 

To operate the motor control/timer, the installer must first 

set the time of day and the day of the week. Please see the 

specific sections of this manual for additional information.

Visually re-inspect the installation. Make sure that guards 

and other protective devices are securely in place.  

All covers and gaskets must be re-installed to minimize  

the entry of dirt and moisture.

www.nidec-motor.com/Pool

MEnu

HIGH SPEED 

o ErrIDE

LoW SPEED 

o ErrIDE

run / SToP

Low    High 

1 :  AM

MTuWThFSaSu

Program

Press Enter to Con rm

Set Clock 

Set on Time 

Set off Time 

override

EnTEr

1

3

4

2

Содержание BADU ECOM2/S90





























Отзывы: