Spearhead Multicut 620 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 31

Spearhead Multicut 620 Скачать руководство пользователя страница 26

Spearhead Multicut

620

26

26

26

26

Clutch

Clutch

Clutch

Clutch Maintenance

Maintenance

Maintenance

Maintenance & Settings

& Settings

& Settings

& Settings

BONDIOLI Manufacture (Belleville Spring)

Check the condition of the friction discs before use and following periods of storage.
Release  the  tension  from  the  spring,  turn  the  clutch  while  holding  the  P.T.O
stationary. Adjust the spring compression to the original setting.
Following seasonal use, unload the spring tension and store clutch assembly in a dry
place.  Check  condition  of  friction  linings  and  reset  spring  compression  to  original
height before use.
Should the assembly overheat due to frequent or prolonged clutch slipping, dismantle
for inspection. The original thickness of the lining is 3.2mm, replace them when worn
to  2.5mm.  Clean  up  all  contact  surfaces  and  replace  any  damaged  components
before assembly.

BONDIOLI

Standard - 3 Blade Per Rotor

Fig No.

Position.

Part No.

Setting.

Machine.

2

Centre (2 plate)

5770223

18.9mm

620 (1000rpm)

2

Inner Wing (4 plate)

5770215

17.6mm

620 (1000rpm)

2

Outer Wing (2 plate)

5770207

17.8mm

620 (1000rpm)

Optional - 6 Blade Per Rotor

Fig No.

Position.

Part No.

Setting.

Machine.

2

Centre (2 plate)

5770223

18.5mm

620 (1000rpm)

2

Inner Wing (4 plate)

5770215

17mm

620 (1000rpm)

2

Outer Wing (2 plate)

5770207

17.2mm

620 (1000rpm)

Note
The dimensional setting ‘h’ applies to later type clutches where the 2 discs being
measured are of equal diameter.

Warning

                                     The slip clutch is there to protect the gearbox.  If the
                                     blades strike a large obstacle they may get damaged or
                                     break - avoid these conditions.

«
...
24
25
26
27
28
...
»

Содержание Multicut 620
































Отзывы:

Нет отзывов