Spearhead Multicut 620 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 31

Spearhead Multicut 620 Скачать руководство пользователя страница 20

Spearhead Multicut

620

20

20

20

20

Transportation

Transportation

Transportation

Transportation

First disengage the PTO drive, fold the
wings  fully  up  and  secure  with  locking
pin  and  transport  strap  (Fig.  7).  Raise
he  machine  up  above  the  height  stop
carrying  the  machine  weight  on  the
height  ram,  this  transfers  pressure  to
the hydra gas suspension system.

Please

observe

Public

Highway

Regulations, concerning the towing of
implements, and securely attach a
registration and lighting board.

Transportation Position

Transport Strap

Note

Note

Note

Note

Before  parking  and  unhitching  your  machine  please  lower  the  height  ram  onto  its
stop  to  relieve  the  hydraulic  pressure,  before  releasing  to  hoses.  Observe  Public
Highway  Regulations,  concerning  the  towing  of  implements,  and  securely  attach  a
registration and lighting board.

Warning

Avoid transporting machine at high speed over rough ground
Maximum speed on highway – 20mph (30kph).

Warning

                                 Do not transport the machine over rough ground on the height pin alone
                                 as any shock loads may cause stress leading to fatigue and failure
                                 Never transport along public highways with the wings only supported by
                                 the hydraulics, always secure with locking pins.

«
...
18
19
20
21
22
...
»

Содержание Multicut 620
































Отзывы:

Нет отзывов