background image

8999129: v1 11/09/2018 

Page 2.4 of 2.9 pages 

 

 

 

Original instructions (ENGLISH) 

Website:  www.spearheadmachinery.com 

 

 

WARNING!

   For machines fitted with hitch adjustment mechanisms, never un-couple the machine without using 

the hitch support jack.  The hitch is very heavy.  Attempting to lift the hitch without using the jack could 
cause strains.  Allowing the hitch to fall suddenly and unexpectedly could result in crushing injury.  Use 
the support jack for lifting the mower only.  Overloading the jack can cause failure with possible serious 
bodily injury or even death. 

 

WARNING!

   Periodically inspect all moving parts for wear and replace when necessary with authorised service 

parts.  Look for loose fasteners, worn or broken parts, and leaky or loose fittings.  Make sure all pins 
have cotter pins and washers.  Serious injury may occur from not maintaining this machine in good 
working order. 

 

WARNING!

   Where hydraulic rams are fitted, release hydraulic pressure from the rams before attempting 

maintenance.  Lower the machine to the ground and lower any wings or securely block them up, 
disengage the PTO and turn off the engine. 

 

WARNING!

   The operator and all support personnel must wear appropriate Personal Protective Equipment.  i.e. 

safety clothing, safety glasses and protective footwear at all times for protection from injury by objects 
thrown from the machine. 

 

WARNING!

   Transport the machine only at safe speeds.  Serious accidents and injuries can result from 

operating this equipment at unsafe speeds 

 

WARNING!

   While the tractor is running all personnel should keep well clear of the area around the machine as 

there are numerous crushing, shearing, impact dangers caused by the machine operation. 

 

WARNING!

   Beware of dust.  Keep tractor cab windows and doors closed at all times to reduce the risk of dust 

and flying debris from entering.  In dusty conditions the use of a suitable mask, to EN 149, is strongly 
recommended. 

 

WARNING!

   The machine must only be lifted by personnel with appropriate lifting qualifications. The lifting 

points are clearly marked with 'hook' symbols. 

 

WARNING!

   Always ensure the tractor front end weight is sufficient to give proper front wheel contact and safe 

steering when machine is raised on tractor hydraulics. 

 

WARNING!

   The operators, manual must be kept with the machine to be available for quick and easy reference. 

 

WARNING!

   Beware of bystanders and animals.  Before starting the tractor-engine and moving off, check that it 

is safe to do so.  Never operate the machine with bystanders or animals near or on the machine or 
tractor.  Never stand in or walk through the flow of any material being discharged. Never stand 
between tractor wheels and the machine. 

 

WARNING!

   Do not start or carry out maintenance on this machine until you have read all the safety 

precautions to be observed and until you fully understand the controls and functions of the machine as 
detailed in the following sections.  If you do not understand any part of this manual, ask your dealer for 
assistance. 

 

WARNING!

   Always fit the PTO shaft guard & check chains.  P.T.O. guard check chains must always be 

attached to a suitable point on the tractor and machine to prevent movement of the outer plastic 
shields. 

 

WARNING!

   It is the owner's/operator's responsibility to ensure that the machine is fitted with correct lighting 

and safety markings when moving it on the public highway during the hours of darkness. 

 

WARNING!

   Never operate the machine with any of the rotor blades missing or damaged.  To prevent injury, 

when changing blades, always block the rotor to stop it rotating. 

 

WARNING!

   Never operate the machine with any parts missing.  Check the machine regularly for loose or 

damaged parts.  Pay attention to the condition of all safety guards.  Always use genuine Spearhead 
replacement parts in the interest of safety.  Failures caused by the use of unapproved replacement 
parts will not be covered by our warranty, nor will any liability be accepted for damages or injury thus 
incurred. 

 

Содержание AG18





















































Отзывы: