background image

www.sparrl.com

 

Sparr Electronics Limited 

Page 5

 

 

 

 
 
 
 
 
 
 
 
 

  

OBD2 Connector Pin Descriptions 

 

7.  Modes of Operation 

It has two basic modes of operation:  

  Mass storage device mode and 
  Data Logging mode  

The device detects which mode to activate based on the connection. If the device is connected by USB to 
a  PC  during  start-up,  it  will  activate  Mass  storage  device  mode.  Otherwise,  it  will  activate  Data  Logging 
mode. 

 

1) 

Mass storage device mode

 

(USB Connection) 

If the device is powered on by the USB-cable connected to a PC, the device will behave as Mass storage 
device.  In  this  mode  the  internal  memory  will  be  reserved  for  PC  to  access.  The  PC  will  recognize  the 
device as a standard USB memory device Drive such that the device storage can be easily accessed. The 
logged data can now be transferred to the PC without the need of  any  special software. Additionally, the 
device configuration can be accessed and modified (refer section 7). 

 

2) 

Logging mode

 

(CAN BUS Connection) 

If the device is powered on through the OBD2 connector, it will activate the Data Logging mode. When the 
device enters Data Logging mode the internal memory is reserved/allocated for data-logging and cannot be 
accessed through the USB-port. As the device enters Data Logging mode it will attempt to read the device 
configuration file located on the memory-card (the device configuration is described in section 7). If a valid 
configuration file  is found,  the  configuration  is  loaded  into  the  device.  If  no  valid  configuration  is found, a 
previous configuration is written to the memory-card and loaded into the device. The device is now ready to 
communicate with the CAN-bus and log messages according to the loaded device configuration file.

 

Note: 

DO NOT CONNECT USB TO PC WHEN CAN BUS IS CONNETED TO OBD2 FOR DATA LOGGING.

 

 
 
 

PIN 

DESCRIPTION 

PIN 

DESCRIPTION 

Vendor Option 

Vendor Option 

Positive bus line 

10 

Negative bus line 

Vendor Option 

11 

Vendor Option 

Classic Ground 

12 

Vendor Option 

Signal Ground 

13 

Vendor Option 

CAN High 

14 

CAN High 

K Line 

15 

L Line 

Vendor Option 

16 

Battery Power 

Содержание CAN









Отзывы: