7
Original instructions
EN
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
▪ Always inspect the blade. Use only well grind
-
ed blades. Never use blades with cracks and
indents or HSS-blades.
▪ The slotting knife must not touch the blade.
▪ Check if the mobile guard moves freely.
▪ Make sure the work piece or the material is
well secured.
WARNING:
Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out.
SWITChING ON - SWITChING Off
- Switching on: press locking button 1 and then
the lever of ON/OFF switch 2.
- Switching off: release the lever of ON/OFF
switch 2.
MOUNTING ThE BLADE
WARNING:
Draw the plug out of
mains socket!
The blade is covered by mobile guard 10 at rest
and during work. Turn the guard over and hold in
this position. Unscrew by Allen key screw 6, while
detaining clamping washer 8 by a spanner or by
placing the blade upon wood. Dismount washer
8 and blade. Mounting the blade is achieved in
reverse order. The supporting surfaces of thrust
washer 5, blade and clamping washer 8 must
be clean. The directions of arrows on the blade
and the immobile guard must correspond.
ADjUSTING ThE SLOTTING KNIfE
Slotting knife 9 prevents jamming the blade. It
should be adjusted so that the distance to top
of teeth and cutting depth must not exceed
5 mm (fig. 1). Tighten the slotting knife by Al
-
len-head screw 11 on the rear of the immobile
guard.
ADjUSTING ThE CUTTING DEPTh
Choose cutting depth 5 mm bigger than material
thickness. Loosen wing nut 3, adjust the cutting
depth by ruler 3 and tighten wing nut back.
ADjUSTING BEVEL CUTTING
Loosen wing nut 13, adjust the cutting angle
according to ruler 13 and tighten wing nut 13
again.
ADjUSTING ThE SAW BLADE PARAL-
LEL POSITION TOWARDS ThE BASE
PLATE (fIG.2)
We recommend to perform this adjustment in
authorised service centres for warranty and
post-warranty servicing of SPARKY power tools,
where the equipment for precise adjustment is
available. If necessary, the adjustment can be
performed according the operations listed be-
low, but any possible consequences are at cus-
tomer’s expense.
- Unwind the four bolts 17, fixing the base
plate to the machine.
- Place the guide of the parallel guide 4 on the
short side of the base plate, the ruler shall lean
against the blade 18 along the whole length (as
shown on fig.2).
- Rotate the machine slightly, so the blade can
touch the ruler along the whole length.
- In this position, lubricate all screw threads
and the joints to the base plate with glue “Loctite
243” and fasten the screws with torque 1,5 Nm.
- Wait for 1 hour prior to initial operation of
the machine, so the glue can reach its maximum
strength.
CUTTING INDICATOR
The right slot in the saw base on the side of the
parallel guide is used as an indicator when cut-
ting vertically, and the left slot - when the blade
is inclined at 45
0
. A test cut is re commended.
PARALLEL GUIDE
Guide 4 is used when cutting parallel to the ed-
ge of a shaped part. Cutting width is adjusted by
ru ler 4. The wing nut should be well tightened.
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
